Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
1.
A. nRF7002 DK(NRF5340+NRF7002)
B. Our PCBA(NRF5340+NRF7002)
We found same application code flash to both. Sample A can work. Sample B can't work and stuck
...
Hi,
I was previously working with W25Q32JVSSIQ, a 32MBit memory device communicating with nrf5340 chip. The QSPI driver was initialized using NRFX_QSPI_DEFAULT_CONFIG()...
Hi,
I’m working with an NRF5340 device paired with a Nordic HID mouse. Currently, data encryption is enabled after pairing, but the encryption and decryption modules are...
Hi,
I want to know if Android Smartphone can be configured as BLE Mesh node? If it can be configured as BLE mesh node, how can it be done using below mentioned library...
Hi.
I would like to set the TX power level for broadcast streams to a higher level then the other radio packets (especially the packets on the primary ADV channels). First...
Hi,
I'm working with nRF5340 Audio DKs.
I'm able to successfully run the audio example in BIS mode (with gateway and headset devices).
My goal is to open another BT...
Hello,
I am developing a PCB with nRF52805. The PCB is small and must be cost-optimized. It also needs to be as small as possible.
For prototypes, I have added a J-TAG...
I was building the "console" sample code found in zephyr for my custom nrf52840 board and I managed to get it to work. But as soon as cryptocell gets enabled, it doesn't work...
Hello,
I need to run nrfutil on a raspberry pi3. The NRFutil executable I use on windows & linux found at https://www.nordicsemi.com/Products/Development-tools/nRF-Util...
I have new nrf9161dk that I'm trying to run the "quick start" guide for. However, when I get to the "Progam" step it fails. This is the error log: 2024-10-03T18:05:08.932Z...
Trying to put nRF52840 in OFF mode and I see the following odd behavior: If I put all the output GPIOs into Hi-Z mode, power consumption measured in-line with the battery...
Hello,
Do the micro controllers out of the box before installing onto a PCB already have a bootloader? What do I need to consider to be able to reprogram my MCU on the PCB...
I'm working with the nrf9160 dk and trying to get a baseline low power project before I add peripherals and application code. I'm using ncs 2.7, and with an empty project...
The idle power consumption (i.e. the current draw between adverts) is 2.4uA prior to the first call of dm_request_add() following reset.
Once a distance measurement has...
Hi, I am actually newbie to embedded system.
My question is how can I upload my code to MCU.
There are very good tutorial about developing with development kit.
So...
