I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I am trying to adapt lesson 9 (FOTA over Wi-Fi) exercise 7 of the DevAcademy nRF Connect SDK Intermediate course. I am trying to adapt it to work with nrf52840 connected to...
Hi, my code will return ATT error code: 0x0E cyclically
I have check some tickets and try to update my central device to
Hoever, it still cannot, the error is like...
I have two projects, project MQTT, that was built around the Secure MQTT Sensor/Actuator sample and project CRYPTO, that was built around the Crypto AES-CCM sample . I am...
I have an NRF52 devkit and trying to install the "blinky" sample for the first time, using VS Code.
I can build the firmware, but when I try to flash I get these errors...
Hi Support,
I'm working on a project where I need to copy the contents of the internal flash from slot_0 to an external NOR flash partition. However, I'm currently unable...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Dear Nordic Team :
1. Are the T-matching (L2/C6/L3) for IC matching and the pi- matching network(C9/L4/C11) for antenna?
2. If we have long trace for the antenna, should...
Hello,
I'm new to this development environment and trying to get one of your projects to build for the nRF9151-DK. I recently installed everything with the latest versions...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
