Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Summary
We are trying to perform a DTLS 1.2 handshake using PSK (Pre-Shared Key) from an **nRF9151 module running NCS v3.0.2, using modem-offloaded DTLS (IPPROTO_DTLS_1_2...
Hello!
I have stored a PSK in the KMU of my nRF54L15, and now want to use it for a Lwm2m client DTLS connection.
According to Zephyr's documentation, the PSK must be provided...
Hi, I'm using v2.7 toolchain and v2.61 sdk, I tried with both wifi sta and wifi shell example, both failed to build when CONFIG_WPA_SUPP=y, if I comment out this config, then...
I have succesfully tested my software that sends gnss location to aws iot with nrf9151dk. Recently I configured software also support also thingy91x. My problem is that Aws...
I've nrf52833dk board, I'm doing i2c exercise from Dev Academy's NRF connect sdk fundamental course. For some reason I used 'Quick Start' option in "nrf connect for Desktop...
Dear Nordic teams :
I would like to clarify the capacitor usage configuration:
1. If the firmware is configured to use the internal load capacitor and I also place external...
Hello,
I'm building a project on a Xiao nRF52840 Plus board. When I built and flashed the firmware, the Nordic LED Button Service does not appear in the nRFConnect app....
I have a custom board with bl54u and NPM1300 . Working fine.
But now replaced with a NPM1304 as it is pin compatible. Worked fine with fuel gauge NPM1300 on SDK 3.0.1. ...
We've derived a DTLS handshake test firmware from github.com/.../l5_e2_sol
Tests have been done using nRF9151 DK, SDK 3.1.0 and modem firmware 2.0.2.
First we verified...
I'm putting together a project that requires a "large" (1500mAh+) rechargable battery, both because of the desire for long times between charges and to enable powering a peripheral...
Hello Nordic Support Team,
I'm working with the Android-nRF-Wi-Fi-Provisioner library ( https://github.com/NordicSemiconductor/Android-nRF-Wi-Fi-Provisioner ) and would...
I'm using the Nordic nRF52840-DK. I'm having a hard time with logging using RTT. Sometimes it works, sometimes it does not. Usually I get a few runs where it works, then it...
I developed a custom application on the 52840DK and have now moved this over to a custom PCB of my own design. I can compile OK and can start a debug session from "main" but...
I am unable to download the nrfjprog command line tools from your website.
I am using SDKV1.8.0 and Toolchchain V2.0.0. in Visual Studio Code.
When I attempt to flash...
Hi,
I have low power environmental sensor. They raise an interrupt that something was sensed and require to read some registers on the sensor via I2C and run a state machine...
