Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
We are using BLE advertizements and Openthread...
I have a custom board with nRF52840 and uses Segger EDE.
In our project we would like to store some info about production to flash memory (DeviceID, production date etc...
I followed the guide Configuring and performing DFU over Mesh ,old firmware was examples\dfu\build\dfu_nrf52832_xxAA_s132_6.1.1_Debug\dfu_nrf52832_xxAA_s132_6.1.1.hex,new...
Hello,
I want am use NRF2401L01 for sending data wirelessly from one device to another device and vise-versa.
The First device is arduino nano(Transmitter) which senses...
I looked at the following question
nrRF2 GATT attribute read callback
and it does not quite answer what I want to know.
What I need to know is do I get signaled by the...
I have followed the getting started, with my new nRF52840DK, with switches at:
Sw6 Default
Sw8 On
VDD selected
when plugged into the USB, LED 5 blinks rapidly, LED...
Hello.
In order to connect multiple units on the previous question page ( https://devzone.nordicsemi.com/f/nordic-q-a/51970/implementing-multilinks-on-multiroll-programs...
I want to develop our PC software to control the USB nRF52840 Dongle to be as a BLE central device，so I need to know the command that the nRF Connect used to do this，but I...
HI as i am new to nrf nordic semiconductor development i have some quetsions regarding application im developing
I am trying to develop Ble application where nRF 52 will...
Hi,
I am trying to add DFU service in ble_beacon example. I am using SDK14 and softdevice is S132_5.0.0 for 52-dk.
I have merged dfu example with ble_beacon and initiate...
Hi,
For my application using softdevice I need ADC update every 400ms and Battery level update every 2sec and string update for HT1632 led driver every 2sec.So I have created...
Starting with the BLE Uart Service example code, I wanted to send longer length packets, so the necessitated modifying settings like NRF_SDH_BLE_GATT_MAX_MTU_SIZE, NRF_SDH_BLE_GAP_DATA_LENGTH...
I can power nrf52832 using USB without any issues.
I see a strange behaviour using external 3.3V adapters. The chip does not turn on. The power supply to the chip is available...
