Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear all,
I am trying to work with FOTA. I am able to run successfully the http_application_update.
But now, I want the device to download a custom firmware that I...
Hi all,
I am trying to set up UART communication on the nrf9160. I am using the nrf9160 DK and zephyr.
I have selected device UART_1 and after I cal functions device get_binding...
Hi,
I am trying to implement OTA updates on iOS. Where can I find out what error 10 means?
Below is the log of events from my app. Please don't hesitate with questions...
Hello guys,
I have nRF52840-based BL654 SoC module on my custom board and I develop the firmware in SDK 15.0.0 environment with s140 SoftDevice.
Among other things, I...
One little example At the bottom of file nrf5SDKforMeshv310/bin/ospace/examples/dfu/dfu_nrf52840_xxAA_s140_6.1.0.hex
We can make it more human-readable by utility from...
Hello,
I'm trying to make custom board based on Thingy 52.
First problem that I get I want to change gpio's order according to my needs.
I can't not find where in the...
Since the manual for the nRF9160 DK doesn't have a full schematic, I'm not sure what sort of power supply decoupling the nRF9160 needs. What are recommended bypass caps, if...
Hello,
I've modified(added custom libraries) an existing example project from the SDK(v 15.3), and I'm trying to build and flash it.
The project compiles fine, but throws...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
When trying to install the nRF Connect app (3.1.0) on a windows 7 machine, it hung up and froze during the Jlink install. After using system restore to go back before that...
Hello we are using SDK 15.3 and SD s140 v6.1.1, we use the cryptocell to do some AES encryption as well as MAC and ECDH.
We noticed that our application was running quite...
Hi,
I'd like to test how long it takes to get a gps signal and send the nmea string via udp. Therefore I took the example 'udp_gps'.
As far as I know the program starts...