We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Does the Thingy:52 use the default transmit power of 0dBm? I didn't see anywhere that it could be changed from the app or that sd_ble_gap_tx_power_set was called anywhere...
Using Keil MDK Lite v 5.22, writing code in C for nRF52, with SDK 12.
Example code works.
How does one declare a function, define it, and call it?
I've created a...
In my debugger, I see that variable error_code is 0x00000004
void app_error_handler_bare(ret_code_t error_code)
{
error_info_t error_info =
{
.line_num = 0,
.p_file_name...
I'm running a debug session.
I set a break point inside of function services_init on line 201.
I ran the run up to break point command
The processor pauses on...
Hi,
i am trying to save data with the flash data storage module. Using this code ( infocenter.nordicsemi.com/index.jsp from infocenter erverything works fine. But when...
I am attempting to do a BLE firmware update via command line tools in an attempt to automate programming in a script file. I have zero problems performing an over the air...
In a project using esb, with two nrf52832 devices configured as default, one as RX, one as TX, with dynamic payload, TX sending packets to RX can change the packet pid (and...
Hi!
I have two PCA10040 boards and I'm running the MQTT publisher example in both using a Raspberry Pi 3 Model B as a gateway.
Therefore, both boards are establishing...
Hello,
I am using pca10028 and sdk 12.2. I am trying to run some code. I am getting some make file error as ble_nus_error.PNG .
My main.c file is New Text Document (3...
Hi,
I have 2 nRF512840 eval kits and tried out the att_mtu_throughput example provided on SDK 13.0.
The throughput about 900-1000Kbps can be achieved with PHY 2.0 DLE...
Is there any way that I can use more than 4 timer in nRF 51 ??
(four or more...)
I'm using Softdevice 130, so It uses Timer 0,
and I'm using RGB Sensor using PWM Library...
i m new in NRF52832, i use saadc exemple pca 10040 sdk 13.0.0, i dont now how to get adc result from the buffer because there is 2 elements in the buffer :
err_code = nrf_drv_saadc_buffer_convert...
