Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi Sirs,
I have 2 modules in Mass Production by using nRF51822QFAA & nRF52832QFAA.
Customer asking us to support Apple Home Kit.
Can get your advise for :
How to...
Hi Nordic Tech Support!!!
Greetings of the Day!!!
I'm Dinesh Katkar, we team working on wearable IoT design and we need to interface 4 RGB LED-SMLP34RGB2W3 from nRF52832...
Hi：
1： NRF52832 How to set up the TX transmission power.
ble_app_hrs ：didn't see set TX transmission powe
2、NRF52832 ：How much is NRF52 maximum rate, how to set
THS...
What are the certifications required for Australia? My device has FCC and CE certifications, are these enough to allow someone to import my device? We are both really unsure...
I'm using the nRF51822 DK + SDK10.0.0 + s110. I'm going to create a system where I do an SPI read from two sensors every 6ms. From these sensors I will get 20B each over SPI...
I'm writing a program sending die temperature data through BLE. I'm trying to combine the nrf51822 Heart Rate Monitor example and the nrf6310 Temperature example. Both examples...
Hello,
I have connected a SX1272 module to a nRF51 Development Kit using the Arduino connectors. Anybody written a sample app to get me going?
There is a SX1276 Ping Pong...
Hi all,
We have implemented the wireless mouse example on some custom hardware and it works great. We need to do something a little different however, and send absolute...
I can run peripheral examples in SDK folder like GPIO, Timer, Scheduler ...
but when I want to Add somethings like GPIO to peripheral_UART_ble or timer or scheduler It didn...
Hi Nordic Community,
I am using the nRF51822 to receive a data stream from the SPIS module and transfer the data directly to a phone over BLE using the S130 softdevice...
This is a follow-up question to devzone.nordicsemi.com/.../
I am using SDK_11 s130 on nRF51-dk.
I discovered that on nRF-UART Android app, notifications are not enabled...
I managed to enable pairing without bonding on ble_app_uart by porting peer manager over from ble_app_gls. I am using SDK11 s130 on nRF51-dk.
I observed some strange behavior...
Hi Nordic's community,
I have an issue when writing uint32_t to a characteristic, i don't understand when i write uint16_t or uin8_t, it works ! but don't when i send an...
Hi,
I would like to add single bank signed DFU support to my project (running on nrf51822AC - 256kb version).
In SDK 10, there was an experimental bootloader with a nice...
Hi,
I want to transmit adv. data AES encrypted everytime. The Basic requirement is to do Encryption with Stream Cipher (Counter Mode) so i want to know when and where to...
