Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
The intent of the implementation is to first connected to a central using fast advertisement and once they are connected the first time, if they disconnect, the...
Hi, i am going to tune my PCB meander antenna by soldering center conductor of semi-rigid coax cable directly on to the coplaner wave-guide trace and outer conductor on to...
Hi, i am designing a board using balun in it. Also, i am going to use meander antenna of nordic dongle(reference image is attached). As i can see, there is no RF coplaner...
Hello , I want know , if i used the Gazell Pairing Library (gzp) , it means that I can not use the ACK
Payload function ？if i can use the ack payload function place give...
Hi,
after reading the NFC with an smartphone the power consumption stays very high without doing anything else...
I don't know if this is related to this bug: "NFCT...
Hi,
I saw in the infocenter that the SAADC can measure the VDD directly. So in my case I want to check the voltage of a 3.3v coin cell regularly, I could do this without...
Hi Everyone,
The On Semi 7150SL reference design incorporates a dongle that can stream stereo music to two hearing aids which are equipped with the Ezairo 7150 module....
Dear sir,
Can we use NRF51822 OR NRF52832 as a slave device .As our controller is STM32F407ZET6 and we did not want to change any firmware from our previous version except...
I am using Keil to compile code and program into nRF51822 chip. SoftDevice s130 is used. There are various types of nRF51822 chips - nRF51822_xxAA, nRF51822_xxAB and nRF51822_xxAC...
Hi,
I need to measure the frequency of a PWM signal with 50% duty cycle through one of the GPIO pins. The frequency of input PWM signal ranges between 100Hz to 1000Hz....
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hello.
I use nRF52 , PCA10040 , S132 & SDK 11.
I want to send data what get through UART to nRF52 from a peripheral, to PC by UART.
Due to, I made this program from example...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
