Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
hi,
i have a project which need dfu by OTA,but nrf51822 flash is not enough.The project detail information in the following:
chip:nrf51822QFACA10
SDK6.0
SOFTDEVICE:7.3...
I'm using nrf_drv_twi to talk to an accelerometer from an nRF51822 on a custom board. I'm on SDK 10.0.0. I'm following the example from the SDK, peripheral/twi_sensor. And...
Hi,
I set advertising data as follows:
err_code = ble_advdata_set(&advdata, NULL);
But I can't achieve advertising without ScanResponse，could you give me some suggestions...
Hello,
I do connections between 2 nrf51 with a known and static services. Is that possible to bypass the discovery to access a characteristics (i know all characteristics...
Hi,
I am having problems using the the dfu_dual_bank_ble_s110_pca10028 example on a nrf51822_xxAA device.
I have changed the memory ares to:
IROM 1: 0x3C000, 0x3C00...
So long story short - I need to pair two devices: Arduino UNO with Seeed BLE Shield and Adafruit Feather 32u4 Bluefruit LE.
Now, Seeed shield is configured, and is able...
Hello, I am now having problems to get NRF51 DK to work. My computer is connected to board with USB. It can recognize it.
Now, here is what is something strange, when...
Not sure if this is the correct place to ask this question.
I can't seem to find the download location for the Master Control Panel PC application. It seems to only available...
Hello,
I am currently trying to generate a PWM signal on P0.00 and am not having success. If I drive P0.00 without PWM, everything works fine. Is there anything that would...
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN...
I'm looking at log_uart_init in the nRF5_SDK_11.0.0-2.alpha and wondering if it would make more sense to allow the application writer to pass in a baud rate.
I'm trying to program a nrf51822 custom board using the SWD interface of the nrf51 DK. The board is using the low voltage configuration.
I'm not duplicating this question...
The IoT SDK Documentation page is getting Error 404 not Found.
Here is the error:
The requested URL /nRF51_IoT_SDK/doc/iot/html/index.html was not found on this server...
