Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I'm working on nRF9160-dk.
I built a sample application "serial lte modem" in NCS 1.6.1.
i can use AT command on the UART0, but i find the printk in source code is not...
I have successfully compiled my project using `west build` and now I am trying to load it onto my nrf5340 board I recently purchased. Here's what I'm doing:
- From the same...
Hi,
I would like to test some environments. Therefore - I would like to use an example from SDK 17.0.2, which allows me to connect to a PC via NFC, as a peripheral, receive...
I'am working on nRF52840-DK and nRF9160-DK.
i'd like to add an interrupt pin for a SPIM device. (eg. in the following spi_dev: )
&spi3 {
compatible = "nordic,nrf-spim...
Dear nordic team,
i want to take log from dfu example i tried using rtt veiwer but it doesnt work.im using sdk version 17.0.2 and soft device 7.2.0 and nrf52840 DK
in...
Hello ,
I am using nRF52832 , sdk 16version. I want to set the BLE connection interval via BLE command using application. How to do that? I tried to assign the variable...
Hi,
I’m using the nRF SDK 1.6.0 and trying to build the “ memfault ” sample for nRF9160 using the
“ nrf9160dk_nrf9160ns ” board. The sample location is:
C:\Users\username...
Hello, after I make the connection to the nrf device with the phone, I found there is only a "Forget This Device" option on its setting page. So is there a method such as...
Hi Nordic,
The bluetooth qualification needs the information of nF5340's value n for Intermodulation test but hard hard to find in any document.
Please help us out, thank...
Hello,
It appears that when the project is generated it is expecting a "../common" directory?
CMake Error at /opt/nordic/ncs/v1.7.0/zephyr/cmake/kconfig.cmake:209 (message...
Dear Sirs,
after "few" hours of testing, I noticed that nRF9160-DK loaded with SLM v.1.6.1 is not working the same after awakened up from sleep (#SLEEP=1) or even from idle...
Hi everybody,
I have developed a project where a central device with multilink, connected to the maximum peripheral as much as is possible (in my case 4 devices more). ...
Hello,
I'm trying to figure out how to get A-GPS data via a GSM modem in places where LTE-M is not availalble.
Does the SUPL library support this, if I populate supl_client_ctx...
Hello all,
I just found out that the nRF Connect extension for VSCode has been release, which is great news. Good job Nordic Team! I have followed the steps described in...
Hi, dear Nordic.
I'm using BC805M Module which uses nRF52805 SoC. What's the max sink/source current for individual pin OR total chip, please? Where could I find relative...
