Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi everyone,
I am using the nRF52840 DK and I am experimenting with the USB MSC example. My purpose is to record data from an IMU device and store them in files. Then to...
Hi,
This is a followup from another issue ( link ) which helped with.
The suggestion to modify nrf_serial.c fixed the previous problem, and you can see that the TE (transmit...
I have an expansion board by ST mounting an analog mic (MP23ABS1). The mic out pin (via a diff. amplifier) is given on a connector. I take that signal and feed it to the AIN5...
I'm trying to ensure my firmware goes into power off when it should, and that current consumption is as expected when in power off. However, using PPK2 to measure current...
Hi,
I'd like to use SPI and I2C simultaneously on nRF52832. But I came across this post which says "if you use SPI0, TWI0 is not available". Does this prevent me from...
I took the I2S example from SDK15 and while compiling I am getting the following errors. I tried but I am not able to solve it. The same happen when I have taken twi example...
Hello,
SDK : 16.0.0 Controller : NRF52840
I have 2 app_timer instance, one is used for longer sleep like 24 hours, and other is used to blink led when device is performing...
If you are broadcasting in normal mode, this code will not report an error. But if you are broadcasting in long range mode, this code will cause a FATAL ERR. If you are broadcasting...
I am wondering if it's possible to conduct a serial UART loop back test on nRF. For example, if I use a wire to connect the TX and RX pins together, and send something out...
My understanding is that Thingy:91 HW doesn’t support FOTA update of nRF52 from nRF91 since the reset control line isn’t connected from nRF91 towards nRF52. My understanding...
I am working with the udp example in nrfConnect for the nRF9160
I see that CONFIG_UDP_DATA_UPLOAD_SIZE_BYTES has the value of 10 (bytes of payload). However, I do not see...
Hi
I have my custom board with nRF9160 module running Serial Lte Modem application, and an external MCU talks to nRF9160 over UART and access using AT commands. The custom...
We are using nrf9160 and Modem firmware 1.2.3. This might be a regression of this bug .
Our concept is to switch the modem on via lte_lc_connect_async(), exchange some MQTT...
Hi,
I have a requirement, using the latest mesh sdk ' nrf5_SDK_for_Mesh_v5.0.0_src ' on nRF52 Development kit(PCA10040), I want to generate the temperature data from DK...
