Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I have created a folder in ble_peripheral in the examples of SDK for my project.
I am using keil uvision 5 and when I have an issue with the sdk_config.h
It states incorrect...
Hi everyone,
I'm using the nrf52832 Dev Kit PCA10040
SDK version: 15.3.0
OS: Fedora
I try to use DFU following this tutorial but I don't get the DFUTarg on the...
Hi pals!
I'm trying to establish throughput test with two nRF52840 DK and it works perfectly well except the coded PHY option. When I configure the phy option to coded,...
HI,
I am playing around with the "usbd_ble_uart_freertos" example of SDK version 15.3.
When I create another Task and try to write log entries (NRF_LOG_INFO("Test")) i...
Hi,
As well know, there have 100 channels in ESB function in nRF52832, but 2.4GHz also share with Wifi and Bluetooth.
So there have many noise if I choice wrong channel...
Hi!
I am experimenting with the ble_app_hrs_freertos example.
I would like to start two additional tasks. All works until a ble conection is made. after that my created...
Hello
I am using FDS to store some MAc addresses in my project. After successful I try fds_init() which returns error 11.
I can't figure out what is causing this error...
Hello, I have been trying to get the nrf9160DK PCA10090 version 0.8.2 to connect to your nrf cloud. I initially tried with the provided ibasis sim. I was able to get it registered...
Hi,Master:
1.The timing of the underlying nrfx_qspi_write(...) function is:a. Send 05 to check if the wip bit is 0. (Here, if wip is not 0, will it always detect until wip...
Hello,
I am going to be heading to a certification house to run tests to pass for the CE mark for our product that we used the nrf51822 on. The BLE portion of our product...
Hi everyone,
I'm trying to establish throughput test using mtu_throughput example(central-peripheral) and 2 nrf52840's but I keep getting error when set phy to coded. Here...
Hello All,
I want to know if I can run all this protocol at once? if yes can I find an example or can you suggest me a guide? I know there are examples to use BLE and ANT...
Hello, I'm attempting to establish a data connection on the VZW network after uploading a VZW IMEI to the ODI portal. It appears there is no module available under the Nordic...
We are incorporating a filesystem for NAND flash driven by the NRF52, but we are running into performance issues using littlefs and want to do deeper troubleshooting. From...
Hi Everyone!
I really need some help. So I'm new to Nordic semiconductors and Segger Embedded Studio IDE. I purchased myself an nRF52832 breakout from sparksfun and nRF52832...
