Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have a project in which I've started from the proximity app example code and added some UART stuff using app_uart.c. The linker is giving me this error immediately after...
Hi,
I'm trying to get an iOS app to connect to a Nordic BLE device. I'm a firmware guy with little app experience but I have gotten a app to work based off the code presented...
Hi,
Im new to BLE and still trying to wrap my head around things. I am using the both new nRF51 DK and nRF51 Dongle for testing at the moment. I know that the old dongle...
I would like to have track time of the day in my peripheral (s110)application. I understood that RTC0 is used by Soft device. RTC1 is used by app_timer application. I have...
hi nordic:
thank you for your great support!
question 1:
App: LightBlue in iOS.
when app scanning for perpherals ,i have found my device,show as "measurement…."
THEN...
Hi all,
I had a working TWI connection combined with BLE advertising. When
I added uart code for printing to putty this TWI connection was no longer functional.
So...
Hello,
I am currently working on a project and I would like to add some security to my device by preventing services from being discovered. Ideally when a user connects...
Hi
I am trying to use the internal ADC to capture an analog value every second. For this I use a timer to wake up every second, start the ADC and go back to sleep.
I...
Is anyone using the third-party BLE module from Taiyo Yuden? If so, where did you find the recommended footprint?
Taiyo Yuden's website only gives very limited information...
In the SDK 8.0 are only examples for nRF51422.
Is it possible to compile this for nRF51822 and is the softdevice 8.0.0 for both controllers?
Best regards,
Roman.
Hello,
i am new to nRF Bluetooth.
My Setup ist:
One Atmel atmega640 and one nrf51822 communication via UART (at the moment).
I am sending data from atmega640 to...
Hi,
I'm writing a bootloader for nrf51822 to be able to update the nRF51's firmware through SPI (data transferred via an STM32 retrieving the file through USB).
My idea...
Hello,
I am trying to write data to flash with the pstorage api. I managed successful to write data to flash with the pstorage_test_store_and_update() function from the...
Hi
Recently we bought NRF51 DK board. Initially when i connect the nrf51 DK board to PC via USB it mounts JLINK driver and on IF/BOOT button it mounts BOOTLOADER drive...
For my application I need to identify the peripheral source advertising packets are coming from. How is this best done with BLE and SDK 7.1? I would prefer not to set a a...
