Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
I am using nRF connect SDK v2.9.0 with a custom developed board that looks like this:
I tried the ' Bluetooth LE LED Button service' sample as it's and noticed that...
Cannot flash, debug or connect to my custom nrf5340 board. It had been working and now I am getting this message in VSCode:
I have also gotten this one on another copy...
I have a custom board (nrf5340) and can debug it, but it will not print to J-Link RTT Viewer. The main looks like this and I tested with a breakpoint on the LOG_DBG using...
Hello everybody! It's my first question and I'm new at mcu programming. I hope for your understanding!
I have a task: count seconds using a counter and display them on a...
Hi，
When I use NCS V2.5.0 （board：nRF 52840），I want to set the Non-Connectable and Scannable Extended Advertising.My code as follows.I use the APP nRF Connect for moblie...
Hello,
I am using a nrf Development kit and I have it plugged in into a mac laptop. It works fine, but I keep getting the message that says:
Disk Not Ejected Properly...
This is the normal kconfig menu.
But it often happens that the following picture does not recognize anything in kconfig
and there is no devicetree option in the action...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
Hi，
In Core Specification v5.4, there is support for Non-Connectable and Non-Scannable Extended Advertising (ADV_EXT_IND) without AUX packets. However, when using Nordic...
When both ethernet and WiFi are supported on one MCU (with both sharing the same L2 implementation, only one network device being active at a time), does it matter if both...
Hello,
I'm working with a custom board using an nRF5340 as its primary MCU and NCS 2.7.0. The application I'm developing requires internet connection and can ideally support...
I am adding OTA support using mcuboot with mcumgr on a custom nrf54l15 board with the upgrade (mcuboot_secondary) partition on an external SPI nor flash (not QSPI). I am using...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hi!
I am trying to power the thingy:91 from solar panels and have some issues with the thingy:91 restarting when the solar panel receives a medium amount of light. The solar...
