Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I recently updated to nRF Connect SDK v1.8.0 from v1.5.0 and am encountering a new error with the same code. The error occurs when I call bt_le_ext_adv_set_data. My advertising...
This is in regards to my last post here: https://devzone.nordicsemi.com/f/nordic-q-a/84016/switching-between-two-applications-using-nrf5-sdk
I am using FreeRTOS.
Both...
During the development process, I had no trouble bonding with the rfConnect (current version from the website). After many changes to code, I got it to bond one time and deleted...
Hi,
Is it possible to use "nearby fast pair" technology on the nRF52833 platform? are there any examples of the use of this technology?
Best regards,
KaEd1705
Hi, I am using libuartes and when I receive text from other device my nrf52833 will respone "textAT1_Uart1". But I can not free them (using &libuartes1 because I'm using 2...
In nordic ncs zephyr use Nordi ble controller (SDC) else in zephyr mainline will use a software version of the controller that use LLL (BLE CONTROLLER).
Il possible to know...
I'm trying to create a minimal executable that has a structure placed at a specific address in flash. It looks like CONFIG_CODE_DATA_RELOCATION is needed to do this. However...
Hello,
we are trying to get the uart secure bootloader running on the nRF52820. When linking we receive the error message that RTC1_IRQHandler is defined multiple times...
For an upcoming product based on the nRF52811 chipset I wanted to prepare for the arrival of the new AP-Protect variant of that chipset and have a unified firmware that runs...
I'm using SDK12 and SDK15 on nRF52832 and nRF52840 (peripheral and central), although this would appear to be an issue with other devices too.
If I connect with NRF Connect...
Potentially related to : nRF Connect v3.9.3 does not detect external j Link programmer - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com) , but I don't see the...
Hi,there:
I was used 2 52832 board to run the linght switch server/client examples to test message communication. I add the mesh events handle like this:
Then run the...
Hi,
I am trying to transfer a dataset of over 100k, via a custom service from a peripheral device.
There are many posts in this forum that describe ways to do this but...
Hi,
I am using two nrf52840 boards and a Light-Switch example included in the mesh SDK_v5.0. The Client sends unacknowledged messages to the Server ( APP_UNACK_MSG_REPEAT_COUNT...
Hi,
We are facing some issues with the DLE update.
The given table shows that the softdevice set data length and time.
Event Length (ms)
ATT MTU (bytes)
Data...
