Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello,
we've got a quite unpredictable issue with a hardfault call : actually this is in this function call : app_error_fault_handler (in app_error_weak.c file)
We use...
I am using the zephyr rtos which run on the nrf52832.
Describe the bug We are using a nrf52832 based board. There are some I2C devices like tsm12 and eeprom. The power consumption...
I'm getting a strange assert from S140 7.2.0 nRF5_SDK_17.0.2_d674dde on a nRF52840 at PC 0x15074.
Frustratingly, it happens a minute or so after boot, but doesn't occur...
Hello Nordic
Im having issues getting logs out of the MSC storage example on SDK16.
When connecting nRF USB connector on the PCA10056 connector to my Windows 10 computer...
Hello,
We use the nRF52832 with SD 17.2.0, Bluetooth LE.
We observe an error when doing the following sequence:
- Build a bonded connection using the nRF Connect...
Hi,
When using the TWI manager you normally provide a callback function that is executed once the transaction has been completed. I'm using the NRF logger module to display...
Hi, Nordicsemi
At present, although SPI uses easy DMA when reading and sending data, in the actual use scenario, I still use gpiote to detect the interrupt pin of the sensor...
I am using the sdk-zephyr. After configing the ubuntu enviroment, i use the west build commond to build the sample project.
But there are errors like these:
[0/1] Re-running...
Hello,
I have few questions about PPI.
----------
1. How to configure PPI channels that runs one after the other? If yes, is there any example?
Because I have two...
I'm having trouble getting the Secure Entry gateway functions to work out of RAM. The nRF9160 datasheet has RAMNSC configurations, so it should be possible. We're able to...
Hello,
I'm not able to locate the QDID for S113 v7.2.0, associated with nRF52832 and SDK 17.0.2.
The product page for S113 indicates that S113 is Bluetooth 5.1 qualified...
Hello,
two part question;
-when a device is registered with the FCC, there is a good amount of documentation uploaded to the FCC website like test reports, photos of the...
Hi I'm wondering if anyone has any tips on implementing a I2C recovery sequence with NRFX 2.3.0 (as included with Zephyr 2.4.99). I've seen this discussed https://devzone...
Based on zigbee sdk 4.1, in the sample code of light_switch, leaving the network and joining the network are completed by buttons, the code is as follows:
Seen from the...
