Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi,
I am working on a project of throughput data from sensors to my central via nrf52832 through a notifying service (SDK14.0.0, S132).
As explained in several questions...
In the Infocenter, there is a section about adding support for custom boards. It advises the creation of custom_board.h modeled after pca10040.h. However, the configuration...
I am starting a nRF52832 project that is based on the GCC + Makefile build system that is provided with the example projects. In my particular case, I need to execute a python...
Hello, everyone~
I'm trying to use mac to develop nRF52832 DK. I have installed the lastest J-Link driver and SES. I downloaded nRF5 SDK 14.2.0 and just open ble_hrs project...
I get nrf mesh SDK form: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
I want to use the serial example to control a mesh...
I use the advertisement timeout to shut down the MCU. Is is possible to reset the advertisement timeout on the fly, e.g. if there is any activity I would like to extend the...
Hi,
I'm interfacing acceleration via BLE using NRF52.
I'm using timer to get the sensor value and update the characteristic value related to this sensor using sd_ble_gatts_hvx...
Hi,
I tried to make a software update (I tried application, bootloader, SoftDevice and any combinations) over BLE using the secure_dfu_ble_s132_pca10040 example but after...
Hello. I have a problem. After using nfc, current consumtion still high. I found that I need use HAL_NFC_ENGINEERING_A_FTPAN_WORKAROUND macros. But when I specify this macros...
Hi All,
I am going to get EMI/EMC testing for my custom board made on nRF52832 WLCSP package. Can you please share/suggest the firmware used in EMI/EMC testing.
hi everyone
i want use s130 with my ble nrf1822 i'm wondering about the modifiaction that i have to do under keil 5 in option for target for example the configuration that...
Hi,
I try to use the dfu update OTA with ble secure bootloader.
If the Flash is erased and only the SD v5.0.0 and the own Bootloader are programmed a update OTA is working...
When making a bluetooth mesh network, what is a good rule of thump for the ratio between servers and clients?
I am thinking of implementing the server-client-model scheme...
Hi Engineers!
We used SDK13 for our Project (multilink BLE with 1xServer & 4x PeerS) and now move to SDK14.2, almost done except only USBD.
if we use SDK13 driver...
