Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
Hi,
I have searched for examples which will use passkey to connect with android, but didnt find any.
I want ble_app_hrs example to connect with nRFConnect in android by...
HI，i develop my project base on “examples\ble_peripheral\ble_app_uart” and “nRF UART v2.0”。i hava large data transmit from phone（androd） to nrf52832。
but when send a package...
I need to save some data on the flash storage. This data will be some structures and I will write, read and modify them as and when required. I am also using peer manager...
Hello
I came across interesting problem I couldn't find answer to.
In my project bss size printed by arm-none-eabi-size is larger than the value that can be calculated...
I'm testing with ANCS example(SDK11.0.0), PCA10028 and Iphone, observing packet with sniffer.
at the first connection,
master sent EDIV( 0x0 ), Rand( 0x0 ), SKDm and...
I'm using an Nrf52 with S132v3.0
I'm using Peer Manager to manage pairing and bonding.
I'm running as a central connecting to a peripheral (iOS/Android peripheral).
I...
Is there any way for the application to be notified by the S110 when a central reads/scans an attribute in the peripheral in response to its broadcast?
There are events...
hi,all
i use use dongle as packet sniffer.when the phone can not connect my device,the dongle can not receive CONNECT_REQ PDU.if the phone can connect with my device,the...
Hi,
I am using legacy version of DFU for my application and would like to use the appropriate version. However, using pip the only available versions are 1.1.1 and beyond...
Dear NORDIC
I have one strange issue:
My nRF52 app work well, then I use Android phone connect to it, it's OK.
Then Android phone cancel pair, so nRF52 disconnect,
...
