Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi, I am using BMD-350-A-R module for a project and i am trying to upload the bootloader and the bootloader settings hex files but those are getting written as application...
Hi,
I am working with a u-blox EVK-NORA- B206 development kit. It has an onboard J-Link and it contains a NORA-B206-00B which has a NRF54L15 inside. I use VS Code with the...
Hi,
Could you provide some examples demonstrating how to use the FLPR on the nRF54L15 with NCS 3.2.1?
Additionally, real-world use case examples would be appreciated,...
Hello,
I am following this course: https://academy.nordicsemi.com/courses/bluetooth-low-energy-fundamentals/lessons/lesson-3-bluetooth-le-connections/topic/blefund-lesson...
Hello,
Developing a new pcb with combined nRF9160, nRF5340 and nRF7000. We want to power the system with a nPM1300 PMIC. nRF9160_VDD on VSYS(4.5V), nRF9160_VDD_GPIO on VOUT2...
The Matter Samples output a verbose level of information to the console as standard. This is a mixture of the application log statements and matter log information. When trying...
Hello,
I am writing to ask a question regarding the power supply configuration when using an external board with the nRF5340DK.
I am referring to page 30 of the nRF5340DK...
Hi all
I have following problem. When using ble_nus_c_string_send to send data over NUS sd_ble_gattc_write returns error 19 - NRF_ERROR_RESOURCES after but the problem is...
Hi Nordicsemi engineers,
While testing a large-scale OpenThread network recently, I encountered an irregular pattern of device crashes. The network consists of 70 devices...
Hi,
I am working with NRF54L05 SoC using NRF Connect SDK V3.1.0 and NRF54L15DK for testing.
I am seeing an inconsistent MCUboot validation failure when flashing a firmware...
As the title, in the project "ncs\v3.2.1\nrf\samples\nfc\tnep_tag", how to runt into function tnep_svc_one_selected()?
I use the NFC tools, Send the hex data, want to select...
Hi, Nordic and all expects.
I am checking whether EN 300 328 can be used for testing 2.4G proprietary mode of nRF 52/53/54 series; EN 300 328 is a popular RF standard for...
I switched from the nRF-bm\v0.9.0 to nRF-bm\v1.0.0 SDK and now I am getting the following linker error message:
c:/ncs/toolchains/66cdf9b75e/opt/zephyr-sdk/arm-zephyr-eabi...
Hello,
I would like to ask what is the maximum number of simultaneous TCP connections that can be operated on nRF9151-DK while using LTE-M?
Alternatively, is it possible...
I am using an nrf54l10 with the NRFconnect SDK. I would be interested in a solution to go into a low power state and wake up again after a specific time (multiple hours to...
