Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
NCS 2.8.0, NRF52840 with accurate crystal LF CLK
I've been asked to tightly synchronize timestamps for data collected by external sensors on multiple boards. The timestamps...
seems like all packs cannot be downloaded from Keil 5. all address are invalid, include all examples.
The requested URL /nRF5_SDK/pieces/nRF_DeviceFamilyPack/NordicSemiconductor...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
I have been working on a project using a nrf52832 and currently have the firmware developed on nrf5sdk. I have been testing out Zephyr with this example https://docs.nordicsemi...
Hello
I'm using the NRF52840DK with a custom shield on top that interfaces to my custom board. I use it to program and debug the DUT via the DK, talk to the DUT over serial...
Hello,
I am working on an update of older FW implementation: nRF52832, SDK 14.1.0, with SoftDevice S132 and using BLE connection.
The change I need to implement is a functionality...
Dear Nordic Technical Support,
I’m currently evaluating the NFC functionality on the nRF7002-DK with the following setup:
Hardware: nRF7002-DK
SDK Version: nRF...
For power-saving we periodically enable/disable the net-core. We would like to use the WDT on the net-core
as well. Since you cannot stop the WDT, how should we handle this...
When I first set up my system I had a color code view of the RAM in my system where the colors corresponded to grouped data objects. Somewhere along the line that view has...
Hello,
I am unable to use the Segger RTT terminal built into the nRF Connect SDK for VSCode Extension pack with the nRF54L15DK.
I have configured my project with the...
Hello,
zephyr: Vanila v 4.1.0
I'm trying to run FOTA via BLE on the nRF54L15DK. I’ve configured everything as it should be, based on the sample:
When I...
Hello,
Is it possible to make the nRF Sniffer for Bluetooth LE application work on a nRF54L15?
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth...
Hi, I am testing the PaWR examples in the NCS and I have few doubts.
In this page , it says in section 1.3 that there are two ways for synchronization - PAST after connection...
From what I can see in the documentation, UART0 is used by default for "non-secure" / application logs and UART1 is used for "secure" app logs. I am needing to interface with...
Hello, I am using an I2S PDM Mic and trying to send the I2S Data over BLE using Segger Embedded Studio. The I2S Program that I have generated is working ok. I have verified...
