Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi all,
I am trying to get started with the Nordic thingy 91 but I am not able to update the latest firmware.
The programmer is only showing one Serial port. The instructions...
Hi Nordic Team,
I have interfaced bme280 with nrf52840 and I got the temperature successfully. I have used https://github.com/knuta/nrf5-bme280-twi link for that.
Here...
hi.
I use nrf52840 sdk nRF5_SDK_17.0.2_d674dde.
I need to control the H and L changes of IO within 300ns, I want to turn on the high-frequency part when necessary, and...
Hi nRF team,
we are building our project on top ble_template_example, and we want data encryption for bluetooth data .
we have seen below ways :-
1.) AES Encryption...
I had a generic USB dongle that I used to receive beacons on my machine from an nRF52832 chip.
To be able to perform OTA DFU, I replaced that generic USB dongle with an...
Dear NORDIC Engineers
I have a qustions about NRF52.We have a project that used NRF52833.We want to add the AOA&AOD function to the project.So I would like to know about...
Building the pc-ble-driver on an Arch Linux machine fails with the following error
./pc-ble-driver/src/pc-ble-driver-4.1.4/src/common/transport/uart_transport.cpp: In member...
Hi,
I'm considering using NRF52832/52840 as BLE central while configuring its I2C as slave.
Should I initialize I2C with TWIS instance? How do I suppose to set the slave...
Hello,
I am using the SMS sample of the NRF9160 SDK version 1.6.1. It allows to automatically send a SMS to a precise phone number, and to receive SMS.
As indicated at...
Hi,
I have been trying to use CMSIS DSP library over nRF52840. I added appropriate CONFIGs in prj.conf file, and cmake file. However, whenever I try to use function from...
Hi,
I would like to change the CDC_ACM UART (CDC_ACM_0) baud rate in runtime mode on nRF5340, but it seems to be not working. Below is my code snippet:
The return value...
Hello,
I am working on project where my requirement is something like... Device will advertise and it gets scanned by its own scanning.
What I have done so far......
Hello.
We are migrating from SEGGER Embedded Studio (SES) to IAR Embedded Workbench (IAR). At that time, an error occurs that "__ICFEDIT_region_RAM_start__" is not defined...
I want to select the nRF52 series SoC as our product platform. I have a use case in which I want to get the optimal channel map and I find the "sd_ble_opt_get()" function...
I have taken over a older (5+ years) project that uses Gazell, but it didn't use the Gazell link layer to do wireless pairing. We were looking at shifting to SDK 12.3 (last...
