Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I was thinking of using our SDCARD/FATFS storage for peer data. Pro's of doing this I can see include.... + wear leveling handled in SDCARD + simple Cons... - slower
I suppose...
Our application is based on nRF5 SDK 17.0.2. Normal bonding (just works) and reconnection works fine, but when the bond information is lost on one side I cannot reconnect...
Just got the Thingy91, While following the first start guide I must have done something wrong because the SW3 no longer puts the nrf9160 into recovery mode / It's not recognized...
Hi. This is my first time using Nordic product, the nrf518222 to be specific. I have been going through the template application code tutorial and I came across something...
Hi,
I have doubts regarding a given scenario that probably some of you have already faced before. Since I'm new to BLE and Nordic, probably my doubts may be basic too...
In generic_dtt_state_set_cb_t the provided p_self is of type const generic_dtt_server_t but the argument to generic_dtt_server_status_publish() lack the const qualifier requiring...
Dear Nordic support
I want to ask you about nRF5x-Command-Line-Tools if
-this software is automatically communicate via internet
-this is not file sharing software...
Hi guys!
I am witnessing the things are evolving pretty fast around Thingy:91! What was up-to-date and actual yesterday is outdated today! That's why I would like to ask...
Hi all,
In the nRF52832 erratasheet, for erratum [220] it states:
"SoftDevice v7.0.1 includes an alternative workaround which does not support FPU being enabled."
...
Hi,
I am having an issue with the FDS update command returning a CRC error as above. Any advice on how to fix this issue would be greatly appreciated.
Steps to recreate...
Hello,
How can I read out the ICCID of the sim card?
I've tried to do it with AT%XICCID, getting error on this.
AT+CRSM=176,12258,0,0,10
+CRSM: 144,0,"98740006819041410210...
Hi
I am using the HW driver library for the PWM.
I looked at your example and in order to change the duty cycle of a channel, you directly change it in the m_demo1_seq_values...
In our current implementation of the CDC ACM output, we use a blocking wait for the APP_USBD_CDC_ACM_USER_EVT_TX_DONE after writing to the cdc acm stack. We are using Teraterm...
Hi,
Someone has been working with Alarm Cluster. I tried to implement it on multiprotocol dorr lock example but it was impossible. I have been reading ZCL library revision...
Hello,
I am trying to PCA10040 example project program to NRF52810 BLE module.
I just know that the 52810 has different(small) memory with respect to the 52832.
So,...
