Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
I am using NCS v1.3.0 examples and also my custom made C++ code with Visual Studio Code V1.48.2 (Since the latest version of VS Code V1.5 is having official issues...
it seems that Figure 2 on this page https://infocenter.nordicsemi.com/index.jsp?topic=%2Fps_nrf52840%2Fpwm.html is incorrect, or at a minimum the figure does not do what the...
Dear Nordic Experts, although the title says it all, please allow me to briefly explain the situation: I'm working on a ble mesh firmware and an accompanying Android app....
Hi,
I have been trying to run nrf9160: AWS_IoT sample on Thingy91 but have been getting the following output in the serial terminal:
I couldn't figure out what mqtt_connect...
The Situation: I am having a Sensor Node that is based on the nRF52832 (S132) and does two things: advertise some sensor data and store sensor data to the internal flash....
I'm porting an application that communicates BLE with a smartphone via nRF52 from SDK15 to SDK17.
It will be Connected, but I can only receive 2 bytes.
Also, even though...
NCS 1.3.0 mbedTLS configuration to the existing app in SES results in compilation error.
The SES project file contains the define like so -DMBEDTLS_CONFIG_FILE=\\"nrf...
I recently came across the Smart Remote 3 product by Nordic. I currently have a product in development that is a remote that has very similar functionality. Even down to the...
Currently I am facing an issue where the board was not able to power up by itself when a USB is port into it. However, when an external source is connected through the debugger...
Hello,
I have a costum board with nrf52832 chip. when I upload example code "/examples/peripheral/uart/" I can see logs coming and loopback test is working great, but when...
I am inquiring about a custom device that hangs in the ble_stack_init(); and the result is a fatal error.
The custom device has an nRF52832
The SDK is the SDK14
The...
Hi,
I am using NRF52810 which acts as a peripheral to send data to the central . The problem is my device is battery operated,So advertising all the times consumes battery...
Hi,
I have Design a new product based on the NRF52840 I am trying to get the lcd up and running so first thing is the pwm for the backlight. I am using pin 1.08 for the pwm...
Hello everyone, We're using a NRF52840 dongle for a Uni project. We got a couple of dongles it. I stupidly used a image on google to know the pinout because it's hard for...
I am trying to use the BluePy Scanner on a Raspberry Pi 3 B+ with a nRF52840-Dongle programmed as a Bluetooth: HCI-uart .
I am able to get the Bluepy Scanner code to work...
