Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi, I already have device that plays audio from sd card. New feature is needed that user can send MP3 file to device from mobile phone that will be stored in sd card and then...
below is a little part of code copied from nrf5_SDK_for_Mesh_v2.2.0_src:
***********************************************************************************************...
Hi team,
I am integrating bmp180 and mpu6050 into a beacon code.While integrating,I am getting the following error
"NRF_ERROR_MODULE_ALREADY_INITIALIZED".
Please help...
SDK14.2
Segger Embedded Studio
nRF52 development board
According to this post https://devzone.nordicsemi.com/f/nordic-q-a/20556/how-does-the-saadc-scan-mode-use-the...
Hi All,
Currently i am working on Zephyr RTOS as a target of PCA10040 DK.I have been compiling and executing a simple "Hello World " example.
While doing cross compilation...
Hello,
I have use the BLE Multi-link Example as a central. For the priripheral I have use BLE Blinky Application and UART/Serial Port Emulation over BLE ( <InstallFolder...
Examples in SDK15 use the Observer pattern to handle BLE events (using the macro NRF_SDH_BLE_OBSERVER). AFAIK, the registered handler runs in some IRQ context, typically higher...
Hello Nordic team
I am working on nRF52832 DK, SDKv15.2.
My question is how we can send and receive more than 100 bytes of data? I know nus services doing it. Also how...
Hello,
On one of our custom board with nrf52832, after programming it like 3-4 times it stopped responding on the nrfgostudio as in it was showing no device detected,...
Hello,
Now i use SDK15.0 and NRF52832 to make a BLE scanner.
I want to scan advertisers every 5s , scan window and scan interval are equal(max=0x3FFF). Also,they are all...
Hi there,
I am facing a situation where I require my BLE Peripheral runs multiple GATT servers instances or add new characteristics to my peripheral to be able to connect...
Hello,
Now i use SDK15.0 and NRF52832 to make a BLE scanner.
I want to scan advertisers every 5s , scan window and scan interval are equal(max=0x3FFF). Also,they are all...
Hello,
Now i use SDK15.0 and NRF52832 to make a BLE scanner.
I want to scan advertisers every 5s , scan window and scan interval are equal(max=0x3FFF). Also,they are all...
The example(s) in the nRF5 SDK 15.0.0 does not log to neither the terminal nor the RTT Viewer. I have enabled logging (I think) by setting NRF_LOG_ENABLE to 1. The example...
