Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
So I reinstalled one of my Linux boxes (again) a few days ago, and one of the things I need to do to get all the development environment up and running (again) is get the...
Hi everyone,
I'm currently working on MAX30100 sensor and i need to read this sensor data with i2c, currently i'm able to read mpu6050 and 9255. However i don't have much...
Hi all,
My BLE device uses the NUS profile to send data to a connected smart device. At the same time it should also be possible to connect to a RPi/Linux based gateway...
I now use nrf52832 to do development, nrf52832 and mobile phones to transfer the data is relatively large, I would like to achieve For mobile phones that support BLE4.2, a...
Hi Everyone,
I have been experimenting around with the low power SAADC example in SDK13.
I am using PCA10040 dev board and I have programmed it to start/stop ADC sampling...
Hi,
We've been developing an peripheral HID over BLE using Nordic's SDK, connecting with iOS, Android, and Windows devices. (Board: nRF52832, SDK 14)
We've noticed an...
Using 2.0.0-1.beta on Linux Mint 18.
Have installed pyserial with: sudo pip install pyserial --upgrade --ignore-installed
resulting in:
Installing collected packages...
hi ;
now after i maked a successful connection between smart phone and nrf51822 and i could change the state of gpio pin 20 i find a new problem
i want my pin is still...
Hi All,
Just wondering if i'm doing the right thing here.
So i am using the example of the central device to get started.The idea i'm trying to do is to use the central...
Hi,
I am working on my production hardware with nRF52840 on it. I am using MBED OS. What should be the memory map of 52840 for soft device and Application code? I am using...
Here are my system requirements:
A single "Controller" needs to send 4 bytes of data per node.
There are 25 nodes in a system (100 bytes total payload).
All nodes must...
Hello,
Is it possible to use Mesh SDK and create a GATT database for mobile device to connect to? There are no examples for this in Mesh 1.0.0 and 1.0.1 except a simple...
Devzone,
I'm working with the nrf51822 dev kit- specifically with master emuator API version 2.1.8.
Does this current release of the API (2.1.8) or subsequent releases...
Hi Everyone. I am Anthony, embedded software engineer. Now I need to dive into the Nordic BLE world for the new project. And we are going to used nRF51822 MCU. But I have...
