Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I am trying to flash custom firmware to Thingy using nrf52dk and nrfgostudio.
I have attached a cable from the debug out port on the DK to Thingy, and followed the steps...
Hello,
I'm using the nRF51822 QFAA and I just came out to this problem:
Is this still unsolved? I always end up in the same forum threads and making 0 progress on how...
About the PCB antenna layout of nRF52810, can i directly copy the reference layout provided by Nordic and paste it on my PCB?
Below PCB layout photo, is i directly copied...
I am about to start using the nRF52 for several projects and would like to know which version of Eclipse is recommended? Since Eclipse can be customized in many ways I'm looking...
i took the original sdk 14.2.0 s132-5.0 ble-uart nus-service example for reference measurements to send data from a 52832 to an android device running nrf uart v2.0
to...
I need to add two more led pins - #10 and #30 - to that board, but I don't know what to do with LED_START and LED_STOP lines, and so far, it is difficult for me to trace any...
Hi i am working on ble_peripheral example on nrf52. i am getting issue in bsp.c
BSP_BUTTON_ACTION_LONG_PUSH' undeclared (first use in this function)
bsp_button_event_handler...
main.c Hi,
I have implemented button long press with APP_BUTTON library with APP timer (a 5 seconds timer).
Normally the detection works fine.
But I found that if the...
Hi,
I'm trying to get BLE pairing example to work. I downloaded the missing micro-ecc library and I encountered this problem: github.com/.../70
So I've compiled this...
Hi,
I try to enable the ram retention function. (Bank 4)
So i used the POWER structure
NRF_POWER->RAM[4].POWERSET |= (POWER_RAM_POWER_S0POWER_On << POWER_RAM_POWER_S0POWER_Pos...
Hi,
We use SDK14.0 with S132 v5.0.0 on a custom board with nRF52832.
In our application using a lot of flash operation, and we found the error PM_EVT_PEER_DATA_UPDATE_FAILED...
Hi,
I am working on the nRF52840 Development Kit and I want to merge between ble_app_uart to usbd_cdc_acm examples.
I opened the usbd_cdc_acm example and added all .c...
Hello.
I have the problem with USB connection with NRF_LOG_ENABLED.
I am using my custom board, NRF52840 QIAABB version. I have enabled CLI over RTT, softdevice. I am using...
Problem: I use a button with a pull-up to wake up the device (nrf52832) from power_off, but by the time the bootloader verifies the application and jumps, the button may have...
Hi guys,
I am developing a appilication using nrf51822 using SDK 11. I am trying to use Fstorage and FDS to store data. I need this data to be updated frequently. As I...
