Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
hi,For the bluetooth certification, but requires a fixed frequency is 2402 2442 2480 test, could you tell me need how to set up 2442 under the fixed frequency?
I'm trying to make one of the examples in the SDK v9, but I'm stuck on the following error;
L:\NR - nRF firmware\Nordic SDK\V9\examples\ble_peripheral\ble_app_template...
Hi,
I use s110_6.0.0 and sdk_5.2.1 in my old product. I found that I can't write flash sometimes. Timer1 and Timer2 are used, and their interrupt priority level is 1(high_priority...
Hello,
I noticed that their was a question in the developer zone regarding MD bit?
devzone.nordicsemi.com/.../
My question is slightly different. I am using Soft...
Is it possible to use random 128-bit UUIDs for custom services and characteristics? Or do the characteristics in a service need to share 96-bits with the custom service UUID...
The hardware bug #39 on the GPIOTE in EVENT mode which gives a overconsumption of ~1mA even in idle mode on, kills the interest of having a low power chip, because the solution...
I am wondering, for 51422 or 51822, are all radios can work simultaneously or only one type of radio can work at a particular time?
e.g., BLE & ANT can work at the same...
Hi all,
Is it possible to get a callback from the softdevice, when a characteristic is changed? If so can you guide me in the right direction - documentation / examples...
@brief Function for application main entry.
*/
int main(void)
{
// Configure LED-pins as outputs.
LEDS_CONFIGURE(LEDS_MASK);
// Toggle LEDs.
while (true)
{
for...
Hi,
I'm using gazell library with app_pwm.
From documentation gazell use Timer2 and PPI channels 0,1,2.
APP_PWM use Timer0.
When I disable pwm using app_pwm_disable...
Hi,
I'm trying to use the nRF52832DK to flash a Rigado BMD-300 module (nRF52) - I've connected SWDIO, SWCLK, GND and voltage sense to P20.
It seems that because the...
I run the boardcast tx application on a nRF52832 board and I add uart drive into the proj. I use UART to console on PC.But uart doesn't work, PC console nothing. What's wrong...
I'm using the mouse example which use bonding and white list which allow to connect only to one central after performing the bonding
my question is, does the bonding feature...
Hello,
Is this the correct setup? What else will I need to do to make it work (e.g. it says something about the MCU will detect the external board and then programm/debug...
I want my device to pair only with a single central device at a time. So once it gets paired, it should not be able to pair with any other device. For this purpose I use directed...
