Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
We have a custom board designed based on N51822, CEAAB0 and we have used the chip antenna from ST BAL-NRF01D3. When we have flashed our proximity code to the device, we will...
Hi,
After i use sd_ble_gatts_hvx() ,i will receive a BLE_EVT_TX_COMPLETE.
The "tx_complete.count" is no problem when i use softdevice 5.2.1 . e.g. count =1. this is correct...
Dear Sir,
i am using pca10001.
Actually i tried to read and write the data from EEPROM having address 0x50 though i2cbus.
i made po.0 and p0.1 as output pin then...
Hi,
I've created a small test program (pasted below) that is intended to help me profile some of my code down to us resolution. Maybe you can quickly run it (no other files...
I'm designing a board using the nRF51822 and leaving test points on the PCB for the programming/debug lines so the chip can be programmed after PCB fab. Are there any reference...
I'm evaluating nF51822 for my application which needs to wake up from either a button press or an interrupt pin singal from an accelerometer. Normally this can be done with...
hi guys, i am writing a code for reading data from a sensor using twi interface, the twi is not working properly, here in SDK i found two examples of twi - sw_ nd hw_ is sw_...
Hi all,
I have read the nRF51822_PS v2.0 and know that nRF51822 supports the SPI slave mode,so I want to know whcih version of the chip will support it?
Also,I have...
Hi,
is possible to reprogram flash in nRF51822 via radio channel?
If yes - is there application note for this feature
Some customer want to secure upload firmware without...
Hello, I need to transmit a data packet with hundreds of bytes, but aparently the S110 SoftDevice can't handle payloads with size bigger than 23 bytes.
According to the...
I load battery_demo_nrf8200.hex into nRF8200. I can then read battery data on Master Control Panel and watch data change when I change VTG.
I then load health_thermometer_application_nrf8200...
We need to customize the Gazelle protocol on nRF51822. To that end we will need access to the protocol source code - not just the API. Is it possible to progress this way...
Hello,I have a ble HID device,
it can connect iphone4S/Ipad with IOS 7 system,
but the function button of (page up /page down) can't work in app wps ppt.
but it can work...
