Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
In BLE service whether can I use same Characteristics UUID ( Ex : using 0x2A6E / Temperature or 0x2A1C / Temperature measurement) with only difference in the description...
We're using nrf52833 and our target board is already running our program well.
Then
we'd like to flash by using Jlink SWD programmer.
So, we connected vref, gnd, swdio...
We have found a nrf52833 DK (PCA101000) with id, 685888541 with 2024.4.
So, it might be used as previous project in our company.
Anyway, I tried to test with this DK board...
based on SDK v2.9.0
1 Central, 4 Peripherals, Repeat the following:
Power off 3 Peripherals, wait a while, power on 3 Peripherals.
The following error usually occurs...
Hello.
I am trying to run an alarm clock using the RTC calendar. In the main loop I see the time being printed, but there is no response from the alarm callback, which I...
Hi,
in my case I need to flash the nRF5340DK board with only a standalone merged_domains.hex , which I get from another co-worker, no source code. how to do it?
Best...
Hi.
I wanna evaluate nRF52840-DK. However, when I tried to install Toolchain on Visual Studio Code, a message "Failed to fetch available toolchains." is displayed. "nRF...
Greetings to everyone.
We have the nRF52840-DK, where the Power Switch SW8 physically is broken.
Is there any way (a bypass, making a bridge/shortcut, using a soldering...
HI everybody,
I have problem with my Nordic nrf9151-DK. I am not able to use GNSS with this kit. A looked at documentation and found, that i have to activate XCOEX0...
Hi,
I have been using the nRF52840 for a long time, and everything was working fine. However, now LED5 starts blinking whenever the USB is connected to J2. I have tried...
Hello, I am new to using the nRF platform, and I appreciate your understanding. I am currently using SDK 2.8.0.
I have implemented a thread in the application core to acquire...
I am working on automating the FOTA flashing process for 50 PCA10056 (nRF52840 DK) boards using a Python script. The goal is to efficiently flash firmware onto multiple boards...
Long story short, I trusted the datasheet (big mistake) where it says an external crystal is optional. In previous builds, I had an external crystal onboard anyway, so this...
Hi,
I am developing Long Range and Pawr using nrf54l15-dk.
For the Long Range example I refer to E:\NCS\v2.8.0\nrf\samples\bluetooth\central_and_peripheral_hr and peripheral_hr_coded...
