What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi, NordicTeam
Nrf52805 as slave and mobile phone as master to connect slave. NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 247, MTU = 23, the master sends the Prepare Write Request to...
Hi,
I'm developping a new application where the device normally is in low power (waiting button with an interrupt)
while(!gIsButtonSwitched) { __WFE(); }
the consumption...
Hi everyone. I have an application using BLE and OpenThread dynamicaly. I am working with nRF52840 chip with nRF5 SDK for Thread and Zigbee v4.1.0 (Release Date: Week 18,...
Hello, I am using the Zigbee CLI Agent as coordinator, and when a router device or end device joins the network I want to configure attribute reporting.
I am able to configure...
We are running a trial in an open field, where we connect NRF52840 ( GW ) to an NRF 52833 (Node ).
Distance between the units is around 80 meter , we are using Coded Phy...
Hi Nordic team
I tried AWS FOTA and Nordic FOTA at nrf connect for cloud. It did work well.
We now want to set up our own cloud. It's neither AWS cloud nor nrf connect...
Hi,
Sorry for the newbie question but how am I going to use the SAADC to measure 4-20mA current loops? I've used the SAADC to measure temperature, voltage, and resistance...
Hello !!
We are using nRF52833 MCU in our one of project. It is very cost sensitive project. We are proving supply to MCU from coin cell CR2032 battery. Also we enabled...
Hi,
I'm currently developing custom board with nRF52832 and I'm experiencing weird issues.
It's mostly related to BLE, especially on Samsung A series devices (A3, A7,...
I am using custom board nRF52820. I'd done OTA up-gradation with USB connected. Firmware successfully updated on device over BLE and device got soft reset.
After removal...
I am using nRF9160 DK(PCA10090 0.9.0 2019.19) with Indian carrier LTE-M SIM and carried below steps to establish LTE-M communication with nRF Cloud: 1. Upgraded to latest...
Dear community,
I opened and successfully tried out the preflash_example. Since I will need a plain text NDEF message instead of an URI NDEF message as used in the example...
Hello,
I'm new to BLE and have a general question about concurrency and collisions. Sorry if a repeat question. I'm developing for nRF52832 using SDK 15.3 and S112 v6.1...
Hello,
I am testing nRF52 UART with DSP.
While transmit data in nRF52 (ADC results)
(example link: https://github.com/NordicPlayground/nRF52-ADC-examples )
I can show...