Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi! I'm configuring RTC on nrf51822. I'm setting up the LFCLK and RTC module by configuring their registers. I have set up a simple IRQ handler, but it seems that it never...
Hi,
I have few question on nRF9160 Thingy:91 and Dev Board.
1. From the schematic, I see that have used SP8T Switch from Antenna Feed pin (GPS and LTE) to the SIngle Antenna...
Hi, we want the DFU code in SDK 10.0 for NRF51 S110 to finish faster. The case we are optimizing is when there is dfu ongoing, just a simple boot.
Currently the main time...
Hi I have included Nordic Thingy52-SESFW to build my thingy:52 file and was at first met with path issues of nordic_common.h and core_cm4.h but have included them by adding...
Hello,
I integrated the nrf-ble-driver static library in a dynamic library that is going to be used in a Windows C# application (through a wrapper), as show the picture...
Anyone know where can I find the online power profiler for the nrf9160?
I was under the impression this was available, but I can't seem to find it anywhere.
hello nordic
i am working on a project with nrf52832
we need to be reading and writing to 2 different tags near the system
is there a Nordic hardware for such...
Hi. I'm trying to use command line tool, but an error occurred as shown in the picture below. Let me know why.
J-link was connected normally in segger embedded studio.
Hi All,
I need to implement security in Bluetooth. I have seen many threads but I could not get proper information regarding how can I implement or add security in a project...
Hi,
I am using the nRF52840 chip and supply iam giving from coin cell(3V). So i want to measure the coin cell voltage level monitor with nrf52840 ADC pin.
kindly provide...
Hi,
I was trying to program my sample to nRF5340's flash using nRF connect v3.4.1 and got this problem:
21:06:02.948
Application data folder: C:\Users\tuan.duong\AppData...
Hi everyone,
I was wondering if you have any advices or recommendations regarding the best type of debugging devices, or ways of debugging, for the nrf52840 Dongle, from...
I want to optimize my receiver power by putting the controller in sleep mode, that is ;-
NRF_POWER->SYSTEMOFF = 1;
And want to wake up the controller only when it receives...
When I try to increase the CENTRAL_LINK_COUNT from 8 to 9 in ble_app_multilink_central example, I got this error NRF_ERROR_CONN_COUNT . Is there a way to increase the max...
Hi,
I wrote a code using gps_controller.c on my thingy:91. However, i could never get a GPS FIX so i decide to try the GPS sample but it doesn't work neither.
I tried...
