after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I'm trying to get the nrf_stack_guard and nrf_mpu libraries to catch writes past the end of the stack. My stack is 8kB in size (0x2000E000-0x20010000). This is the log...
Hi,
I'm working on the custom board using nrf52832 chip and have performed the secure bootloader using ble on the custom board.
I have made these changes so far on the...
We want to connect provisioned node to multiple mobile application over same mash network (Note: We are trying to give access to multiple user(using multiple mobile) to connect...
Hello!
This may be the wrong place to ask, but I am in search of a gateway (off the shelf or a reference design), that incorporates 802.15.4 through the nrf52840, cellular...
Hi,
I just have a small question: say I have two models, both with publish timeout intervals configured. After some time, one model's publish timeout handler is called....
Hi to everybody,
I'm developing over nRF5 SDK v. 3.2.0 a Zigbee node in router role. In my network I've four of my nodes plus several commercial led light driver and a coordinator...
Hello!
I am setting up SEGGER on my mac. Completed all the steps in Getting Started Assistant. But in the last step at "Set up a project in SEGGER Embedded Studio" where...
Hi,
I am evaluating a project where I want to run light switch on nrf52840. This is supposed to support mentioned protocols - BLE Mesh, Thread and Zigbee, but NOT concurrently...
I plan to connect an nRF52810 bluetooth output to a Johansen Tech 2450AT07A0100 chip antenna via a Johansen 2450FM07A0029 impedance matching chip. Do you have a BT SIG approved...
Hi, I am using nRf9160 with last sdk (master branch) and Segger Embedded studio V4.52. When I compile and run any program everything works, but when I try to debug the program...
Hi community ! Imagine this configuration :
A -> B -> C
So A can't directly communicate with C. I send a message from A to C (And only C), so this one with be relayed...
Hi,
I am working on project which is based on nrf9160. I added the source files and user define header files . and also given the path of source file in CMake file. Build...
Is it possible to configure the Zephyr UART parameters like the hardware flow control dynamically at run time? We do that in an nRF52840 firmware with the nrfx libraries ...
Hi all:
Our usage scenario is to establish a connection and bonded between the NRF52840 peripheral device and the central device, and then restart the NRF52840 peripheral...
