Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi guys,
I want to use a smartphone as a poller and the NRF52832 as a tag device. I use typical, high-rated apps desired for sending and receiving data by NFC. I tried the...
Hello, this is my first post on DevZone:-) I'm working with DWM1001-DEV board. I know that this board contains an nRF52832. I'm configuring the SAADC to measure the battery...
Hi
When I use the SDK 15.2.0 & Mesh 3.10.
This light_switch example of advertising bearer(Mesh Profile 3.3.1) default to using the channel 37.
So,I try to change the...
Hello , I started a new project with bluetooth mesh for which I am using Nordic development kits for testing. Nordic offers a provisioning application for the mesh network...
The download for the latest nRF Connect linux client (3.1.0) is linked to the wrong file.
The correct download link is available on the github releases page: https://github...
Hi,
I want to sample ADC signals and send data when requested via BLE or UART. I set a timer that triggers every 100 ms and gets ADC data. To store the data, I would like...
Hi. I'm using nRF52832, SDK13.0.0.
I need to use ECDH curve25519.
I just realized that Oberon has 25519.
There is Oneron library in ble_app_eddystone example.
I think...
I have written a flash code using fds in which i am trying to save the data 7pages(1024 each). I have defined array of record key and fie ID for it.The problem it saves for...
Hi. I'm using nRF52832, SDK13.0.0.
I need SHA256.
My code is
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256);
const nrf_crypto_hash_info_t hash_info_sha256 = { .hash_type...
Hello,
Using nRF5 SDK v15.3.0 Peer Manager drops Service Changed indications if an ATT MTU exchange is in progress, this hapens because function service_changed_cccd() in...
Hi there,
We need help with BLE bootloader.
Here's our setup: nRF5_SDK_15.3.0_59ac345 52840, Production PCB SES compiler for bootloader IAR 7.60 for our production code...
Hello,
I am using nrf52832 SDK 15.3.0, in Segger Studio IDE.
When i am using NRF_LOG_FLUSH in my application , then application is getting stuck in the below code:
...
When the transmitter frequency is 2445MHz and the receiver frequency is 2413MHz, the receiver will receive the data from transmitter correctly. Not only the receiver can receive...
Hi, currently I use nRF Connect v3.0.0 to flash my nrf9160-DK. With the Segger Studio from Nordic I am able to generate the merged.hex but now my problem: I erased the chip...
Hello
I would like to compile Direct Test Mode on Segger embedded Studio.
I follow all instructions with getting started assistant
but i have one error : error 5 cannot...
