Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi, Does anyone know how to modify the asset tracker so that rather than point to the AWS URL it points to a fixed IP address?
Also is the port number fixed?
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) using device: EYSHJNZWZ (nRF52832)
When connecting...
Hi,
When I test nRF MESH application on android phone with other mesh device, after discover services, it always use proxy data in to write data to device for provisioning...
Hello there,
We are planning to use MQTT and nRF5 boards in the project. We've successfully tested out MQTT examples provided in the SDK using BLE router on Raspberry Pi...
Hi,
We are trying to establish communication between ESP8266 and NRF52832 over uart using Baudrate 115200, We are also controlling the ESP8266 boot and power through GPIO...
Folks,
I have read through a lot of threads on here trying to solve this and believe I have tried everything to no avail.
I am finding that I cannot get the nrf52832 to...
Is it possible on the central device to create secure and unprotected connections simultaneously with different peripheral devices? How should the peer manager be configured...
Hi,
I'm writing an application to communicat on BLE with an IoT device.
I connect well, and can write on characteristic but normally I should receive notification after...
infocenter.nordicsemi.com/index.jsp
<info> app: peripheral init ok <error> nrf_sdh_ble: sd_ble_cfg_set() returned NRF_ERROR_INVALID_STATE when attempting to set BLE_CONN_CFG_GAP...
Hi,
I was wondering if there is some kind of SIP client example code available (or in progress) for the nRF9160? For a new project, we are investigating to use the nRF9160...
I'm currently working with nrf52832 implementing bluetooth and spi functionalities. The bluetooth connection to PC is working fine, it connects and after that starts transfering...
Hi,
It seems I am unable to open the asset tracker application in SES. I get the following CMake error:
I've followed the nRF Connect SDK getting started app, and all...
I have a BLE device acting as a central and a peripheral, relaying information between that peripheral and a custom iOS app. As a central, it reads (not notifications) the...
Hello everyone,
I have a question regarding logging errors on debug console (UART or RTT) while using ZigBee stack:
My problem is that I can't get any debug print when...
