I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I write some function, it can run ok before I start he BLE function.
When I start the BLE function, the function can not run ok.
but , I get some data from APP throuth BLE...
Hi,
I've written code to use the "gpiote in event" to sense an interrupt from a peripheral (acceleromenter), but as soon as I enable the in event, I notice the current...
Hi everyone,
I was having RAM overflowed with stack issues which were resolved using suggestions here . Now I am facing another issue. While running mqtt I can only do...
I am trying to use the Scheduler to create my own event handler system (similar to a Ti 8051 OSAL system). I'm writing separate classes that can push data/trigger handlers...
Hi,
I use the BDS v1.1 and nRF Plugin 1.2.2 (from 23.Dec.15). My goal is to simply generate a code for the cycling power profile defined by the Bluetooth SIG. I dont change...
Hello, in the NRF Toolbox UART application for iPhone if you navigate the the UART button screen and connect to the nrf52 eveything is fine. You can exit the app (whitch goes...
After some days trying a very simple tx/rx, reading each page of the manual, looking at at this developer zone, etc. I´m still in trouble, with many distinct partial results...
Hi,
I have a problem with my SPIM read buffer.
As you can see below, my SPI device received bytes correctly and answer correctly
My code is based on SPI example...
In the simple_uart.c there is a code:
void simple_uart_put(uint8_t cr)
{
NRF_UART0->TXD = (uint8_t)cr;
while (NRF_UART0->EVENTS_TXDRDY != 1)
{
// Wait for the...
Hello. I wanted to use a receiver on a quadcopter and some becons nearby(+-5 meters). Is it possible to determine the distance IN REAL TIME to the drone?
I'm a newbie to nrf52832 and would like to ask a dumb question here: can I use radio notification to implement a dynamic advertising message? I've looked into this question...
Hi,
As I know that one reading operation requires 2 connection events:
First - ATT Read Request
Second - ATT Read Response
GATT Read Message Sequence
My question...
Hello.
I'm working with the nrf52 with s132 loaded.
There is a way to have a 6Mbps on the SPI ? I try the value 0x60000000 but this do not work.
Thanks.
Eric Provost.
