Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
After a few minutes of running, the Power Profiling kit will start printing out "Range not detected" messages in the console. It appears to be related with the "Average" window...
Hi,
I am using mca8652fc and used device address as #define ACCELEROMETER_ADDR 0x1D
but it is not reading WHO_AM_I register properly.
I used #define ACCELEROMETER_ADDR...
I did try SPI interface between nRF52-DK and MAXIM11300.
Unfortunately, I did not successfully it work.
I used SDK_11.0.0 on nRF52-DK 0.9(Engineering B) and that
...
Hello, according to devzone.nordicsemi.com/.../ it was an example in nrf51 sdk 6.1.0. I checked it and found no files or folders related, not in sdk 6.0.0 or sdk 7.0.0 Could...
Hi,
I need to send my packets with an interval smaller than 100ms in unconnectable mode. I know, that this is a restriction from Bluetooth standard. For my application...
Hello,
I've a problem with handling interruption on nrf51dk (SDK12.1.0).
I set GPIOTE to handle interruption based on the example code "pin_change_int".
I work with the...
I am trying to use the NRF51 soft device with the App_PWM library. I can get both working individually, but when I try to enable both, I can no longer connect to the device...
Hi ,
I am trying to interface SD card with nrf52. For this I am using fatfs example of new 12.0 sdk. I can able to write the data to file but when I am taking the data...
HI,
I followed this link github.com/.../nRF51-ble-bcast-mesh to develop mesh in nRF51822 dongles. i am able to flash the code( nRF51-ble-bcast-mesh/nRF51/examples/BLE_Gateway...
Hello, I am working on characteristics tutorial.(our service.c)
And I succeeded in notifying characteristic from nordic to android.
The methods I used to notify characteristic...
I'm in the process of migrating to SDK 12.2 and I noticed that nfu_dfu_settings.c now includes app_scheduler.h and makes a call to app_schedule_execute().
How do I use...
want to send a float as a value of a characteristic
I have successfully achieved this using the simple way
Below is the example of just two float variables in an array...
Hi,
I have a PCB with a nRF51822 QFAC A1 onboard, and I wrote a firmware with mbed for this PCB in which P0.08 is supposed to be set to 1 during the initialization and...
My company is in the final stages of prototyping and we want to release our first product in the coming year (focusing on European and American markets). The next steps are...
