Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
I'm trying to program a nRF51822 custom board using Debug out pin P19 of NRF51-DK through Keil MDK, here is the problem I encounter:
To simplify I just use the simple blinky_s130_pca10028...
Hi,
I'm developing simple bluetooth app, where I'm using 3 custom services, each one has characteristic with notification option.
But only the first service notification...
At infocenter.nordicsemi.com/.../anomaly_832_91.html it says that for the IC Rev. Engineering C, build codes CIAA-BA0:
Average Sensitivity over all channels degraded...
Hi,
I am creating a custom project using Eclipse Managed Make having followed the instructions from here .
I am continually getting the above error when I try to Debug...
I'd like to add a capslock function in gazell when i am developing a keyboard based on 'nrfready_desktop_2_v3.1.0'. After i have read the source code from nordic, i cant found...
Hi,
I have a strange problem with FreeRTOS xTimers not waking up, that I so far have tracked down to be related to PPI driven SAADC combined with FreeRTOS Tickless Idle....
I'm working with the experimental_writable_ndef_msg example. I can write data to the tag and the data shows up in m_ndef_msg_buf . I'm writing 2 text records, and I'm trying...
I want to open a sequential space for saving my data, about 20KB , and I want to modify or read it anytime, nordic suggest using FDS, but it seems a bit confusing. Is there...
Now, I can write the data to flash(but only once),and I can read data from the flash.
Those all be OK.
But I want to write data more than one times.
So,I use the NVMC to...
NRF52, SDK 12.1
We are using I2C to communicate with a secure element. We got the basic system working and can send and receive APDUs. The problem we have is when receiving...
Hi,
is it possible to flash the nrf52 with a TTL-232R-3V3 cable. My initial idea was to connect the cable uart Rx,Tx pins and program it using nrfjprog .
However, the...
Hello,
i'm new in bluetooth programming. but i wish to make a bluetooth controled frequency generator. Frequencies must be in range 1 too 1000 Hz, with variable Pulse Width...
Hi,
We found out on this topic that there was a flaw memory protection of nrf51xxx chip
devzone.nordicsemi.com/.../
We search on the net and found out quickly how...
I have an old application which I want to add the bootloader and secure DFU.
I have to migrate to SDK version 12 and I have some persistent data which the old program is...
Hello, I have nRF51822 Beacon Kit (pca200006). I'd like to upload .hex file in DFU over ipad, I picked beacon example from sdk 11. When I point on the hex file from ipad toolbox...