Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Is there a call to read the stack ID.
For example S120 v2.1 has an ID of 0x006B . nRFgo studio is able to read and report this value.
Is there a way to read for me to...
I'm using SDK 11.0 and example\ble_central\ble_app_hrs_c
I have cut SB1 SB2 to disconnect the 32Khz crystal from the pca10028 and configured the example program to use...
Hi, When I write data synchronously to memory (nRF51822), I do :
APP_ERROR_CHECK(pstorage_block_identifier_get(flash_handler, 2, &block_handler));
APP_ERROR_CHECK(pstorage_clear...
Hi,
Im having a problem with connecting my phone to nrf DK.
im trying with apps from examples and they work well with HTC one, but my Samsung S6 fails to find device ...
I flashed dual bank ble bootloader from newest SDK (6.1.0) and used it to load my application to chip. I also modified my application (according to instruction here: devzone...
Hi, I have two device. S120 Scanner and S110 Peripheral Device.
At Scanner, I use SDK 9.0.0 and S130 1.0.0, At Peripheral Device, I use SDK 9.0.0 and S110 8.0.0 ..
Scanner...
hello,
I have a custom board which works fine with SoftDevice+Application , but if i Combine a boot loader hex that i complied it doesn't work. But the same ( bootloader...
I found and implemented an example that gives me a decent idea of how to go about polling for data with the UART/FIFO. However this doesn't give any indication of how to use...
Hi.
Trying to set up the Ubuntu development environment for you nRF52 development kit.
I followed this tutorial:
devzone.nordicsemi.com/.../
Stuff done so far:...
I am using the nRF51822 chip. The RAM memory is composed of two blocks (0 and 1) of 8kB each, divided into 4 sections : Call Stack, Heap, Application, and SoftDevice.
If...
Hello,
I have migrated to the latest version of the sdk11. However, I get a nrf error 4 when I call sd_ble_uuid_vs_add. Multiple people on this site have been having this...
I am trying to port blinky_blank (no SoftDevice) to my target and started by creating a custom_board.h header file with correct GPIO pins for the LEDs and duplicating blinky_blank_pca10040...
Can anyone help me reading IO capability in Android? Basically there is a known bug in some Android versions across different manufactures where Android reports wrongly IO...
