Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am working on S120 v2.1.0 and SDK 9.0 for central and I am able to connect to my iPad. Now I need the central to delete the bonding information stored using pstorage...
Hi All,
I am wondering if I could upgrade from S110 to S130 over the air.
What I see in the S110 and S130 hex file is that the MBR is different. Not many bytes but it...
I see that there is a 1.2 Volt VBG reference available for the ADC but that reference doesn't seem to be available for the low power comparator. Is there any undocumented...
I'm developing a central providing NUS client services to multiple concurrent peripherals. I had code working reliably under SDK 9.0.0 based on the NUS client example in github...
Hi, we looked at your BOM for matching components in your file:
www.nordicsemi.com/.../15787782
for QFAC variant of the IC. You use LQP15MN27NG02D as 27nH inductor which...
Hello guys,
I am using this repo to update my device's firmware but after the update is complete, the iPhone cannot find the correct devices services anymore.
To detail...
We're using the NRF51822 and the S130 with V9.0 SDK, and we're using most of the features of the SDK for our Firmware; but I'm running into a problem flashing the device on...
I'm rolling my own very simple PWM implementation (I'm not using the PWM example code). My code is below:
#define GPIOTE_CHANNEL_NUMBER 0
#define PCLK16M 16000000
#define...
HI:
I use gzell protocol to realize 2.4G communication with SDK 5. I wonder that is the gazell protocol update in SDK9 or SDK10 ? and is there any improvement in latest version...
Hello:
I want use nrf51822's time/ppi/gpiote to capture the pwm rising/falling range duty.I want to know the most numbers of pwm channels duty parameters it can capture?...
Hi everybody,
as Nordic is currently working on this "Internet of things" thing and there are plans for an IPv6 over Bluetooth stack, I was wondering if it wouldn't be...
Is there a calling context restriction for sd_ble_gap_connect()? Either in the function call or where the peer address pointer is in memory?
I based my Central project...
Hi everyone,
I tried to test nRF51-ble-app-uart-static-passkey to learn the static passkey method.
I used PCA10001 EK board, with S110_7.1.0 and SDK_6.1.0.
Well, if I connect...
The maximum data length of a characteristic is 9, and I use the follow function to send the notification to a client
uint32_t dxs_send(dr_ble_dxs_t * p_dxs, uint8_t * p_data...
