I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hi, I'm trying to write a long byte array with the nrf master control panel on android. I'm unsure if the app is able to, but in any case I'm not getting the event: BLE_EVT_USER_MEM_REQUEST...
Hi,
I have my custom nRF51822 board, and i used to flash the firmware through nRF51 DK kit.
As there are two ports through which we can load external boards i was using...
Hi,
I'm trying to build a prototype using the Adafruit nRF8001 Breakout and an mbed ARM CPU.
After Reset, I get a Device Started Event, telling me the chip is in Setup...
Hi,
In SD100v8, there is capability of checking the application version, to make sure no downgrade (or any other criteria required). The reference is in Link to SDK
...
There is a blog post for advertising but none for connection interval.
I am wondering how big is the difference for this example:
Measurement on peripheral every 4 seconds...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
Hi,
Got stuck on an issue that has come and gone and then working fine, and are now back again.
I use a nrf51 module with the led-button-service example (sdk 5.2). It...
So, we are pretty far along in development (I have inherited the project) with an nrf51822, SDK 4.4.2 and SoftDevice "6.0.0-alpha". We are nearing release, and I was told...
I have set the POFCON to enable the power failure comparator and set the voltage level to2.5 volts. How do I know when the battery voltage is below the 2.5 volt level? How...
I want to try a UART communication without RTS & CTS
my board is PCA10001, and I use the SDK 6.1 example: uart_example.
I use Serial Port Utility to communicate with the...
Using SD_110 v6 I get a hardfault on the final call to sd_nvic_EnableIRQ(SWI2_IRQn);
sd_softdevice_enable before that returns success. Any idea why enabling interrupt could...
Hi,
I'm trying to implement an existing proprietary protocol on the nRF51422 SoC. In this protocol the device address is placed differently in the frame than the predefined...
I want to confirm with Nordic staff that the MBR compares the new bootloader with the one it will replace when executing SD_MBR_COMMAND_COPY_BL. It seems that after a comparison...
