Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
We have the Nordic nRF54L15-DK PCA10156 0.9.3 2025.19
We use nRF Connect for Desktop v5.2.1 and Programmer v4.7.2 and connect by USB to our ASI_nRF54L_DK1 001057739416....
Does Nordic have any libraries or solutions for negotiating with a USB C charger and requesting 9VDC for example? Or do you recommend that I use a separate dedicated ASIC...
nrf5340 NCS 3.1.0
Hello, I am trying to improve boot time and here are some spikes and timings. What I have found out is that CryptoCell init (hw_cc3xx_init_internal) takes...
Dear Nordic Team,
I'm currently working on an application that uses ACL and ISO to transmit data between 2 devices. ACL is used for transmitting operations that are then...
Hello,
I am developing using nrf5340 and optimizing the Bluetooth throughput currently.
Although experiments go well, there are a few things I would like to know more...
Recently, I've been evaluating the I2S interface of the 52840 to read ADC data from the TLV320ADC6140 chip.
The TLV320ADC6140 datasheet states that the chip supports TDM...
Hello everyone,
I’m a student currently working on a university project related to BLE-based positioning using the nRF54L15 and Channel Sounding .
In the documentation...
Zephyr board: nrf54l15dk_nrf54l15_cpuapp
Hi, we have a custom SPI NAND flash driver and are trying to create an external flash partition for our littlefs file system.
...
I'm very new to Zephyr so please be patient with me. I'm looking for an example that show me UARTs running on the following pins and setup. I have the echo_bot working with...
Hi
There is a github repo https://github.com/nrfconnect/Asset-Tracker-Template/tree/main that receives updates as of yesterday.
However on the documentation website...
I'm trying to get a previously fully functioning MQTT connection back up and running after some hardware difficulties, but am failing to get it to connect to the MQTT broker...
Looking for an example to adapt into my program.
I detect 'smp_svr' but compiling it give me error, it seems I need a flash configuration in file pm_static.yml, but I have...
Dear Nordic Support Team,
We are currently developing a new product utilizing the nRF9160 LTE-M module.
We are in the process of acquiring CE certification for our end...
Hi,
I have been facing issues with the configuration of the nRF9151 for sending and receiving UDP packets via the Skylo NTN network.
I am running firmware version:
...
Hello, on my nrf54l10 I observed a pin (GPIO 1.03) being actively driven low for ~20 ms during a reboot (e.g. Resetting after SystemOff Mode). I need this pin to stay high...
