Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hi,
I am using Mesh SDK4.1.0 and BLE SDK 16.0.0. I was testing the Light lightness implementation and I see that the Default value of default lightness is 0xFFFF. But the...
Hi
I read in another post a while ago a suggestion of changing GPIO pins allocated to the UART (which I can't find now) as a way for implementing multiple UARTs. I would...
Hello.
I having problems with reading a value from one of the ext pins on thingy 52. (i can set the pin as output and toggle the pin from code.)
i have configured the...
before the question , I hope you understand my poor English.
i make a project using nrf52840 dongle and study how to use dongle
I debug pca10056 example on dongle...
Hi. I'm developing IMU system for multiple purpose using ICM20948 & nRF52832.
But there are problems on TWI communications when using BLE simultaneously.
If not use BLE...
I am unable to get logging working. (This is the subject of another issue I have raised, logging does not work in the hrs freertos sdk 16 example.)
I'm trying to read...
Hello,
I am trying to communicate with a sensor hub using I2C. Whenever I debug it enters into a while loop (_disable irq).
But this is not the repetitive. Some help...
Hi All,
I'm trying to create a hybrid program using the USB CDC ACM example as well as the flash_fstorage example from SDK16. I've been able to get the USB CDC ACM example...
I am using nRF5 SDK 16 on a Rigado BMD-300 (nRF52832) series evaluation kit. The application receives button presses and releases from a peripheral (characteristic change...
Hi, I developed some functions on nf52832, nrf52810 and now I'm with nrf52811. I'm able to put some debug on tx pin so I can read it from PC COM, I use app_uart which use...
The earlier post covers the details of our current project:
https://devzone.nordicsemi.com/f/nordic-q-a/55474/aoa-aod-direction-finding-support-in-nrf52833-sdk-v16-0-0-and...
Hello,
My questions is about ANT and CRC :
Does ANT stack already use a CRC that checks if a data has been received correctly?
Or do I need to create my own when sending...
Hi,
Sometimes our custom board is not readable with the reader uTrust3700 from Identive and it might be related to this post . We are usind SDK 14.2 with our custom board...
I'm using nRF52832 and intend to interface 3 I2C slave devices; the first is the BNO055 IMU.
I've integrated the Bosch "driver" code into my SES project, but I find that...
We are implementing a DFU controller to perform DFU over serial for the nRF52832.
Our reference is the nRF5 SDK v15.3.0 DFU Serial documentation (Nordic/SDK/nRF_SDK_15.3...
