Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Hello,
I am facing a issue with the LN service. I am notifying the position at 10Hz and this work well. I have implemented a custom service that allows to send a file by...
Hi,
Just as the title says, I want to use nRF52840 as a peripheral(s140, v7.0.1, BLE_NUS_MAX_DATA_LEN is 244) and using NUS.
And it may pair to a nRF51822(s120, BLE_NUS_MAX_DATA_LEN...
Dear
I got a problem about SES when I create a indepent transferable project for PCA10059.
Background:
I have success to modified a light-swich server from PCA10056...
Dear All,
I need to understand how the Asymmetric Encryption work in BLE. From Nordic, I get to know the following that following are the nrf_crypto frontend modules
...
Hi,
I"m looking for a solution to automatically build the emproject file from the directory *without using any IDE) so that i can export the .hex file and can be used...
Hi.....
I get the following error fault from my device (nrf 52840 with freertos ,using SDK16.0)
the Fatal id: 0x2000B730
what caused Fatal id: 0x2000B730 ?
Hello,
I developed a project based on thread CLI example. Everything works fine but I would like to add more commands to the CLI interface, maintaining the existing Thread...
Hello:
I am using nRF Connect v3.3.1 programmer to flash nRF9160 and got an error.
Silk on nRF9160 is: nRF9160 SICA B0 191601
Programmer can't recognize nRF9160 after...
Based on 52832, sdk15.3 running ble_app_hrs example, requesting MTU through nRF connect, the first success, the second time is unsuccessful, the app prompts Error 4 (0x4)...
Is there an application note or single set of instructions on how to get debug/log output via the SWO output rather than RTT or UART. Both of the latter are simple switches...
I'm trying to hook up a nRF51 to two other devices. One is connected with UART and the other through BLE (NUS).
The connection with BLE is working fine. But as soon as...
I am using "ble_app_hrs_rscs_relay" example. I am not able to set the TX power of advertising and scanning both. Currently the avg current is too high.
I also tried using...
Hello, in my travels through Nordic development, somehow I am only now creating truly custom characteristics, and I realize I have no idea why there is both an initial and...
Hello, when I run the subject example and connect to it, I see the RX and TX characteristics like I'd expect.
However, I see a descriptor on the TX characteristic which...
Hello! I am trying ZigBee multi_sensor example.
(I had a question here as well. Thank you. "Zigbee multi_sensor example has not connect" https://devzone.nordicsemi.com...
