Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi Guys
I need your advice. I have a customer that is currently in production with the NRF52840 . They now require direction finding but need a Nordic Evaluation kit to...
Hello,
I am new to Nordic platform, previously i had worked on TI controller.
I have three questions to ask:
1) My firmware consists of four services, each service...
hi,
I am using nRF52832 with KEIL. I want to use version6.0.0 softdevice, but I can't select from KEIL runtime library.
Also, the version that can be downloaded from...
I am trying to change after 10 seconds into non-connectable mode. I am using the below code for initializing:
I want to change mode into non-connectable using this type...
When I use dfu_nrf52832_xxAA_s132_6.1.1.hex, it works all devices updated with blink code as described in dfu_quick_start.md But without any provisioning Process, why? And...
Firstly , I have 2 phone. Phone A is huwawei using android 7 and Phone B xiaomi pocophone using android 9.
Phone A already success connect using UART. But I want to try...
I have a same question:
https://devzone.nordicsemi.com/f/nordic-q-a/22025/in-nrf52840-not-able-to-program-boot-loader-hex-is-using-nrfgo-studio/86420#86420
But I not working...
Hi, I am trying to run the following demo here: https://github.com/NordicPlayground/nRF52-ble-long-range-demo
I have followed the instructions and copied the demo folders...
In my understanding, only Nordic NRF Connect (Android and iOS) can be used to bootload a device using the Nordic DFU.
Is there a corresponding command line tool to perform...
I followed the issues from https://devzone.nordicsemi.com/f/nordic-q-a/54149/error-by-loading-solution-on-ses, which fixed the zephyr script issues, but was seeing the same...
Hi,
I have migrate to SDK14.2 the MPU9250 exemple from the peripheral folder in the nrf52-pesky exemples : https://github.com/e27182/nRF52832_pesky https://github.com/e27182...
I am using the nRF52840 DK with the s140 softdevice and am trying to copy the interrupt vector table to RAM to modify interrupts during run time.
I run the following function...
I am porting the eMD-6.12 firmware/library by Invensense for the part MPU9250 into the nRF52832. My toolchain is compiling through gcc allowing examples from SDK's to be quickly...
Hi,
We 're currently using an ARM SOM that will run Yocto Linux from NPX for our current project. We have the nrf52840 connect to this SOM via USB, and we want to be able...
