Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
We 're currently using an ARM SOM that will run Yocto Linux from NPX for our current project. We have the nrf52840 connect to this SOM via USB, and we want to be able...
I am using SDK V15 with an nRF52DK and Keil compiler.
I have difficulty finding an example to use a GPIO to drive a Piezo Buzzer. The requirement is very simple: use a GPIO...
Hello,
Is there anyone successful in communicating with an nRF52 based GATT server from a Windows 10 App? I’ve skimmed through the forum and do not come across any positive...
Hi,
I have an application that verifies a chunk of data and EdDSA Ed25519 signature against a remote public key.
The device application generates a random number, sends...
Hi,
I would like to add some custom sensor for Thingy:91 board. I notice that there are no GPIOs available to connect sensor to nRF9160 SiP? So do I need to connect the...
Hi,
Today I found I was unable to flash my nRF9160 DK. "west flash" fails with the error message "Installed nrfjprog is too old for the device. Please upgrade nrfjprog to...
I am trying to follow the section “Declaring custom cluster” ( https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.thread_zigbee.v3.0.0%2Fusing_zigbee__z_c_l...
I've tried for two days to log back into the cloud service and just get the spinning angles. I tried to create a new account and the same. I was able to change the password...
Hi all, I would like to implement a fault handler in our nRF9160 based system to handle hard faults/unhandled exceptions by resetting the system, but am having a hard time...
Dear Nordic team,
I have a running NRF52 with a firmware based on the freeRTOS demo. To this demo I added the PDM Support Module and the TWI Module.
As soon as both sensors...
We are trying to implement models inside the mesh. So we've started with a functional example of the generic on off and tried to update it according to our needs.
The custom...
Hi,
I have 3 devices that all act as broadcaster and observer they continuesly sending data to each other, now i want to establish a connection between one of those 3...
Hello,
I have 2 pieces of nRF52840 and I managed to connect each other. One is central, uploaded the code: 'nRF5_SDK_15.3.0_59ac345\examples\ble_central\ble_app_multilink_central...
NRF52832 DUF success but when download from segger studio, Jlink RTT viwer print NO DFU found, but when download bootloader from segger stuio, can not entry app
Dear Nordic...
