Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I am using the nRF52832 chip with an SDI connected microSD device. I am able to communicate with the microSD card formatted as FAT32, store data, read data all with the FATFS...
I made my own board in which nRF9160 is populated. It's connected to JLink through SWD. SWO is not connected.
I tried rtt debugging and seems to work correctly, but I'm...
Hello,
I am trying to include bsd.h to my project.
simply typing '#include <bsd.h>' is not enough. I need to add directory 'nrfxlib' but I have no idea how to do that...
Dear Support Team,
We are working on nRF52832 based custom design. We had interfaced 3 different sensors (i.e. one with SPI and 2 with I2C bus mode) and sending continuous...
I am facing a strange situation with my app. After turning off all my peripherals and switching to the most minimal code, I see quite a lot of current consumption and that...
So I'm completely new to bluetooth and I've been trying to set up the nrf52 dk pc 10040, but I can't seem to find any recent tutorials to set it up and I don't know where...
I am running flash_fstorage_example on the nRF52840 DK with SDK 15.0.0
I am having some problems with the example, as below:
1. When I run the example and use the shell...
Hi, I am trying to do MQTT disconnect, but I am always getting an error. First I successfully connect to the MQTT server, then I send some data, and then I want to disconnect...
Hi, I've been trying to use the nRF52840 Dongle to act as Bluetooth 5.0 peripherals but I cant seem to configure them for Long Range (coded PHY) detection. I am currently...
I ran one of my 9160 DK boards for 10 days using the Asset Tracker demo. The Hologram SIM card site I used says data exceeded 1 MB, which I understand the limit. Although...
Hi,
I have been trying to print out the float values using the NRF_LOG_FLOAT_MARKER, and i am only able to print 2 values in a single NRF_LOG_INFO line. Is there a way to...
Hello! I'm following the nRF52 Dongle programming guide to adapt the USB examples from SDK 15.3.0 to the nRF52840 Dongle. USB CDC ACM works fine, and I managed to get half...
Hello everyone,
I tried reading around the devzone and the infocenter , but I still didn't manage to solve my question.
In my scenario I'm using:
an nRF52832 as a...
Hi,
Sorry to bother you in your holidays.I want to get an conversion every time by calling nrfx_saadc_sample( ) .So I had configure saadc like below.But I found the adc...
