Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi. I have been looking through the forum to find anything that could answer my problem, but can't seem to find it. I am working a project, where our needs is to use a nrf52...
Hi there ...
In Softdevice S140 v6.1.0 started supporting advertising extension with this macro "BLE_GAP_ADV_SET_DATA_SIZE_EXTENDED_MAX_SUPPORTED" and I follow the migration...
Hi Team,
I am using nrf51822 for my project, i have connected a PIR Sensor and a push button also a LED driver WS2811 .
I am using ble app uart example as i have to control...
Hello,
I'm looking for 3D STEP model of nRF52840 QIAA aQFN73 package. I just found step model of dev kit, but not component itself. Could anyone help me and share one. ...
Hi,
I was trying to follow the steps for this example: https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
However, I reached step 5, where I should compile...
Hi,
I am developing a bootloader for a custom board with the nRF52840 (nRF5 SDK v15.0.0 and SEGGER Embedded Studio V3.30) where we have no other option but to engage DFU...
Hi ,
I am working on application in which I am using GPIO pin to detect interrupt. GPIO pin normally has logic low level. When it becomes high level I have to generate...
We develop BLE server application on nRF52840 with SDK 1.5 using nRF52840-Preview-DK.
The application is built as multi tasks with freeRTOS where BLE is one of the tasks...
Hi,
I am using Keil uVision 5 and SDK 15 on nrf52840 development. NRF_LOG_ENABLED is set to 1 in sdk_config.h
But NRF_LOGS are not being printed in Debug(printf) viewer...
Hi,
when the micro go in: idle_state_handle(); I have 2 possibility:
If the soft device is present use the first instructions else the second.
This is correct, but...
Dear nordic,
I have an BLE application which works as Central and Peripheral and also which contain ADC,UART and GPIO's
Scanning and advertising controlled by application...
Hi Team,
We have observed that without power supply we are seeing 1V power at board Vcc. Without giving power supply to board.
Why is this happening?
We measured GPIO...
I was trying to verify boot loader using the provided script. I noticed following abnormality.
--It often fails to verify and show the following error:
Reading UICR...
Hi
I'm running nRF52840 MCU at 1.8V, and trying to use the dev kit (PCA10056) to program the external nRF52840 MCU.
According to the datasheet, the dev kit runs on...
