Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
We are transitioning a product from the nRF51 to nRF52832, and I am looking into what I need to do to get our code ported over and approved with the Bluetooth SiG. ...
Hi there,
I am a using a nRF52/SDK 13 to communicate to an external board which uses AT commands, I would like to save some battery during the time I perform my AT command...
I read that the old SDK for mesh had the provisioner and client as the same operation, as I am trying to make my own philips hue style wireless lamp I would need to get my...
Hi!
My question is for the purpose of power calculations for both the nRF52832 and nRF52840 for BLE use only.
I haven't been able to find a reference for this.
I see...
I'm trying to follow "Bluetooth low energy Advertising, a beginner's tutorial" by MartinBL found at https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble...
Hi, in my previous attempt to fix n52DK, I fixed the n52DK board's power rail. It turns out not the problem of the interface MCU shorting VDD.
But when I followed the instruction...
Hi All,
Just feedback from Lab, they said that they can set any channel frequencies at bandwidth = 1MHz in the Direct Test Mode. BUT they said that they need to test any...
Did someone try to make QT application that supports DFU for BLE devices? Can it be done using nordic DFU android/ios libraries (to include them somehow in QT project)?
Hi,
I am having a problems with USB enumerating with a custom board based on the nRF52840. The board is self powered by LiPo battery. I am developing by connecting to the...
Greetings,
I'm attempting to use the ble_connectivity example for the PCA10040 and have a couple questions:
1) What are the default GPIO pins for UART?, for SPI?
2)...
Can you provide an android application that can implement light control?A s shown in Illustration:
like the nRF Connect or LightBlue.the application as client not provisioner...
HI:
I am studying mesh now.But I don't know how to run this example.I think,that proceed as follows:
1.Using provisioner example Configuration each node(element and models...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
When I execute the code below in ble_stack_init (void) , I get an error...
Hello, I am a beginner with the nRF51822, after reading documentation and posts on this forum I can not find a clear answer for these two questions: - Is it possible to modify...