after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I have a multiprotocol application and I'd like to do BLE scanning for as long as it's possible. For now I made 30% to 70% BLE to Thread, and it's the most I can give...
Hi,
I'd like to be able to use an event from the LPCOMP to sample the RTC (either to a peripheral's register, or to a memory address), so I can measure pulse widths without...
Hi there!
I am running the Thread Border Router example and have successfully loaded RaspPi_OT_Border_Router_Demo_v1.0.0-1.alpha.img into the RaspberryPi 3B+.
The problem...
Hi,
I've modified light switch client to read input from GPIO pins . I used int_pin_change as a reference for initializing inputs. The Int_change_pin example uses interrupts...
Hello, I'm developing an debugging an BLE application. I'm using nRF Sniffer (dongle) N51422 PCA10031. I can successfully sniff and decrypt ble secured connections of my application...
Hi all, I want to add light switch client to light switch proxy server . But I dont know how to get appkey handle for bind to light switch client . Pls , help me !! Thank...
Hello,
I'm unable to capture packets using the sniffer. Here are details regarding my set-up:
System: Debian 9.4 with kernel 4.9.0-4-amd64 #1 SMP Debian 4.9.65-3 (2017...
Many of the pins in the assignments page of the documentation are designated as "Standard drive, low frequency only" and I cannot seem to find an explanation of what is considered...
I am trying to connect my android mobile with nRF 52DK using BLE on the NRF TOOLBOX android application. But the nRF 52DK is not recognize by the NRF TOOLBOX APP(proximity...
Hello,
we have a problem using the SAADC module with the low power mode, particularly after execution of the NRF_SAADC->TASKS_SAMPLE task.
Before taking a sample, the...
Hello,
I have some questions about ble_conn_params.c in SDK14.2
Question :
1. a. Why do you need to handle four ble conditions ?
b. Shouldn't just send connect parameters...
I hope to use a acceleration sensor with nRF51822 dev kit. So I should use three ADC input. I tested getting one ADC data using adc_simple example(Keil_v5/ARM/Pack/NordicSemiconductor...
We use nRF52832 ,when new android phone will connect to this device by mac,we cannot connect to it successfully,we must scan to find the device first,after found it,we can...
I want to t o ensure the stability of BLE connection for BLE frequence calibration,but i don't know how to get the nordic into the test mode and broadcast the empty packet...
