Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
I download the mesh sdk from: http://www.nordicsemi.com/eng/nordic/Products/nRF5-SDK-for-Mesh/nRF5-SDK-for-Mesh/62377
Compile the light_switch/server project for nrf51422_s130...
I am working on an nRF51822 central BLE device. I am wondering if it is possible to lower the clock speed / underclock the device to save power? I know this will make it run...
Hi,
Can we test Nrf52 Advertising extension feature with nRF Connect app in mobile?
Do we have any other app whrere we can test this feature using nRF52832 DK?
Does the following SOC,
nRF52840
nRF52832
nRF52810
have sub 1-ghz RF ? by reading it seems that it is having the 2.4 Ghz RF.
I was looking for 433 MHZ or 863...
Hi.
I want my peripheral, an nRF52832, to accept a connection from the first peer it sees and bond with that peer, and thereafter accept connections only from that peer...
Hello
I am using sdk version 14.0 and softdevice S332. I successfully tested on the nrf52832 board using the ant bsc example.
However, when we put the code on our custom...
Good evening,
I am trying to implement queued write (long write) into ble_app_uart example. I am using s110_v7.1, nrf51822(pca10028), can not find version of sdk it is...
I have enabled radio notifications (through sd_nvic_ functions). When sd_ble_gatts_hvx() (notification) is called once, I've noticed two radio active-nactive windows occur...
Hello,
I have a bootloader with a low power wait for power button on startup.
When I do a BLE DFU update of bootloader + SD + appli, the Nordic smartphone application...
hi
I have a application use NRF52832 to scan beacon's advertising and write the advertising data into NRF52832's advertising.
I found the working current is nearly 3mA...
Hello,
I am useing NRF51822-QFAC in my BT bridge project; Now I need to design the matching circuit; there was some recommended matching circuit in the datasheet(11.3--11...
I have a central device that uses BLE to scan for a specific device (there is only a single device it can bond with). Right now it checks the UUID and the mac address of all...
my device giving output as square pulses.but would like to control current from the range 50uA to 500uA of square pulses.how to calculate it. can someone help me
Hi,
I have a question that Product Specification v3.1 of nrf51822 describes Flexible Power Management: 2.6 μA at 3 V ON mode, all blocks IDLE. But, in the same place, NRF52832...
Working on migrating my application from sdk 12.2 to sdk 14
except for some flash issues most of it seems to be working as before, except I notice this message in jlink:...
